The evaluation of residual axial load carrying capacity of Reinforced Concrete (RC) columns to explosion load is significant for protection of buildings. The few investigations conducted on residual axial load carrying capacity of RC columns when subjected to blast loads. Therefore, the overall aim of this research is to generate equations on the blast capacity of axially and uniaxial loaded columns. In this study, an advanced nonlinear model is developed to study the residual axial load carrying capacity (Presidual) of RC columns to explosion loads using Arbitary Lagrangian Eulerian (ALE) finite element technique in LS-DYNA 971. The ALE model represents the actual blast incident scenario and is validated with experimental study reported in the previous research. In order to derive the Presidual empirical equations, intensive parametric studies are carried out to investigate the effects of column depth (d), longitudinal reinforcement ratio (ρ), transverse reinforcement ratio (ρs), yield stress of longitudinal steel (fy), yield stress of transverse steel (fyt), column height (H), column width (w) and concrete strength (fc) on the residual axial capacity of RC columns. Based on numerical simulation data, nine empirical relations are suggested to predict residual axial capacity of RC columns. The validated equations can be used for quick assessment of existing RC columns when blast loading is required to be considered especially to evaluate the blast resistant capacity of a critical building such as military buildings, government assets and etc.
8 November 2023 in International Journal of Protective Structures
Ultra-high performance fiber reinforced concrete (UHPFRC) is a cement-based composite material mixing with reactive powder and steel fibers. It is characterized by its high strength, high ductility, and high toughness and such characteristics enable its great potential in protective engineering against severe dynamic loads. In the current research, the dynamic performance of the concrete panel made with ultra-high performance fiber subjected to explosive loading was investigated. For this purpose, several concrete panel samples were considered and modeled in ABAQUS finite element software. The accuracy of the numerical model is verified by comparing the numerical simulation results with available testing data. First, the considered panel was modeled with normal concrete then it was modeled with UHPFRC concrete, and the effect of using this type of concrete on the behavior of concrete panels was investigated. After analyzing and examining the models, their behavior such as the degree of vulnerability, more vulnerable points and changes in the locations that occurred in each of the models were obtained and compared. The results demonstrate that the use of UHPFRC significantly improves the blast performance of RC panels by reducing maximum and residual displacements, enhancing damage tolerance, and increasing energy absorption. The results also indicate that the increase in the intensity of explosion has increased the base reaction force in all panels.
The prediction of the ultimate bending capacity of the rectangular concrete-filled steel tube (RCFST) beams strengthened with U-shaped carbon fiber reinforced polymer (CFRP) sheets is limited to using the existing empirical models. Thus, this study aims to develop a new theoretical model based on a stress block model to predict the ultimate bending capacity (Mu) of the RCFST beams strengthened with a U-shaped CFRP-wrapping scheme. For this purpose, 28 finite element (FE) models of CFRP-strengthened RCFST beams had been analyzed for further investigation of the flexural behavior and longitudinal stresses distributed along with the beam’s components (steel tube, concrete core, and CFRP layers). The main parameters investigated are concrete compressive strength, steel yield strength, number of CFRP layers, and CFRP-wrapping-depth ratio. In addition, the Mu values obtained from the FE models of the current study and those from the existing experimental tests performed by others are used to verify the corresponding values that are theoretically predicted by the new model. The comparison showed that the proposed model is moderately conservative, as the predicted values of Mu are, on average, up to 10% lower than those obtained from experimental tests and FE analysis.
28 July 2026 in International Journal of Protective Structures
Assuming that the threat of a terrorist attack cannot be entirely eliminated, protective measures must be incorporated into reinforced concrete (RC) structures to mitigate the damage caused by explosive blast impacts and to prevent collapse. The primary objective of this study is therefore to evaluate the damage level of RC columns retrofitted with Fiber Reinforced Polymer (FRP) composites when subjected to high-amplitude, short-duration blast loads. A systematic investigation of various column strengthening techniques using FRP was conducted through blast simulations performed with LS-DYNA software. A finite element (FE) model of an RC column retrofitted with FRP composites was developed, including detailed discussion of material models, strain rate effects, and loading methods. Validation of the FE model was carried out against experimental test results. In this research, the residual axial capacity of the RC column was selected as the damage criterion. The results show that at a scaled distance of , an unstrengthened RC column exhibits a damage degree of (high damage category). Retrofitting with a 5 mm FRP wrap reduces the damage degree to (a 33% reduction), while the combined FRP wrap and strips configuration achieves (a 62% reduction, low damage category). Increasing FRP thickness beyond 5 mm provides diminishing returns. Furthermore, probabilistic fragility analysis is performed to quantify the probability of exceeding damage states, and empirical prediction equations are derived to relate damage degree to scaled distance for each retrofit configuration. These quantitative results demonstrate that FRP retrofitting, particularly the combined wrap and strips configuration, is highly effective in ensuring building protection under blast loading.