During the extrusion of aluminum alloys profiles using porthole dies, the temperature of the material in the welding chamber is one of crucial parameters determining the quality of longitudinal welds. In order to extend the permissible temperature range, the billets intended for this process should be characterized by the maximum attainable solidus temperature. Within the present work, the homogenization of AlZnMgCu alloys DC-cast (Direct Chill-cast) billets was investigated, with the aim of solidus temperature maximization. Conditions of soaking and cooling stages were analyzed. The materials were homogenized in laboratory conditions, and the microstructural effects were evaluated on the basis of DSC (Differential Scanning Calorimetry) tests and SEM/EDS (Scanning Electron Microscopy/Energy-Dispersive Spectroscopy) investigations. For all examined alloys, the unequilibrium low-melting microstructure components were dissolved during soaking, which led to the significant solidus temperature increase, in comparison to the as-cast state. The values within the range of 525–548 °C were obtained. In the case of alloy with highest Cu concentration, the application of two-step soaking was necessary. In order to take advantage of the high solidus temperature obtained after soaking, the cooling rate from homogenization must be controlled, and the effective cooling manner is strongly dependent on alloy composition. For high-Cu alloy, the solidus decreased, despite the fast cooling and the careful billets preheating being necessary.

The extrusion of hollow profiles from hard-deformable AlZnMg alloys by using porthole dies encounters great technological difficulties in practice. High extrusion force accompanies the technological process, which is caused by high deformation resistance and high friction resistance in extrusion conditions. As a result of high thermo-mechanical loads affecting the die, a significant loss of dimensional accuracy of extruded profiles can be observed. The different projects of porthole dies for the extrusion of Ø50 × 2 mm tubes from the 7021 alloy were numerically calculated and then tested in industrial conditions by using a press of 25 MN capacity equipped with a container with a diameter of 7 inches (for 7021 alloy and 6082 alloy for comparison). New extrusion die 3 with modified bridge and mandrel geometry and a special radial–convex entry to the die opening was proposed. FEM was applied to analyse the metal flow during extrusion, geometrical stability of extruded tubes and the die deflection. The photogrammetric measuring method was used to evaluate dimensional accuracy of tubes extruded in different conditions and geometrical deviations in porthole dies elements, especially the bridges and the mandrels. Research revealed a high dimensional accuracy of tubes extruded from the 6082 alloy and from the 7021 alloy by using original extrusion die 3, while much higher dimensional deviations were noted for tubes extruded from the 7021 alloy by using extrusion dies 1 and 2, particularly in relation to the circularity, centricity and wall thickness.

Within the present work the homogenization of DC-cast (direct chill-cast) extrusion billets of Al-Mg-Si-Cu alloy was investigated. The alloy is characterized by higher Cu content than currently applied in 6xxx series. The aim of the work was analysis of billets homogenization conditions enabling maximum dissolution of soluble phases during heating and soaking as well as their re-precipitation during cooling in form of particles capable for rapid dissolution during subsequent processes. The material was subjected to laboratory homogenization and the microstructural effects were assessed on the basis of DSC (differential scanning calorimetry) tests, SEM/EDS (scanning electron microscopy/energy-dispersive spectroscopy) investigations and XRD (X-ray diffraction) analyses. The proposed homogenization scheme with three soaking stages enabled full dissolution of Q-Al₅Cu₂Mg₈Si₆ and θ-Al₂Cu phases. The β-Mg₂Si phase was not dissolved completely during soaking, but its amount was significantly reduced. Fast cooling from homogenization was needed to refine β-Mg₂Si phase particles, but despite this in the microstructure coarse Q-Al₅Cu₂Mg₈Si₆ phase particles were found. Thus, rapid billets heating may lead to incipient melting at the temperature of about 545 °C and the careful selection of billets preheating and extrusion conditions was found necessary.

Extrusion welding of AlZnMg alloys encounters great technological difficulties in practice associated with high shaping forces and the low quality of longitudinal welds. Three different chemical compositions of 7021 aluminum alloy, differing in terms of Zn and Mg contents, were used in the first stage of the research. The laboratory device modelling the behavior of metal in welding chambers of the porthole die was applied to examine the ability of 7021 alloys to produce high-quality joints. The weldability tests were carried out for different welding temperatures—400, 450 and 500 °C—and for a fixed welding pressure of 300 MPa. The microstructural effects in pressure-welds were evaluated with the use of OM and SEM/EDS. The temperature–pressure parameters in the welding chambers were analyzed by using the FEM method for original porthole dies while extruding tubes with dimensions of Ø50 × 2 mm. Finally, the industrial extrusion trials were performed with examination of the structure and strength of the seam welds. It was found that it is possible to produce high-quality high-strength welds in tubes extruded from AlZnMg alloys in industrial conditions (the strength of welds in the range of 96–101% of the strength of the basic non-welded material) through properly matched alloy chemical composition of the alloy, construction of the porthole dies and temperature–speed conditions of deformation.

In the realm of modern architecture, the demand for materials that combine strength, durability, and aesthetic flexibility is ever-growing. Addressing this need, this paper presents a study on the innovative use of aluminum extrudates in construction. Focusing on the AA6005 alloy, which is known for its excellent balance of strength, corrosion resistance, and weldability, this research delves into the development of an extrusion process that yields thin-walled, lightweight, yet high-strength structural components. Using FEM simulations, a new extrudate of the AA6005A was developed. It is compatible with standard façade systems, with high-strength properties and a weight reduced by 20% compared to that of conventional extrudates made of the AA6063 alloy. Using CAD engineering and FEM simulations of aluminum extrusion process, an innovative die was designed for the extrusion process, ensuring uniform flow of metal from the bearing and minimizing the elastic deflection of the die. This resulted in an increase in the extrusion velocity of thin-walled extrudate from AA6005A by 24% compared to conventional profiles extruded from AA6063. As part of the research, a trial test was carried out in production conditions and the quality of the extrudates was tested by 3D optical scanning, mechanical and structural properties tests, and microstructure observation.

In the first part of the work, the 3-step homogenization procedure was carried out for AlMgSi(Cu) alloy, aimed at obtaining billets microstructure with numerous fine particles of strengthening phases and increased solidus temperature. In the second part of the work, an original on a global scale prototype device for the dynamic stretching of extruded profiles before artificial ageing, was proposed and tested in semi-industrial conditions. The thermo-mechanical treatment of extruded hollow profiles from AlMgSi(Cu) alloy with 1.22% content of copper was performed with dynamic deformation range: 0.25%, 0.5%, 1%, 1.5% and 2%. The microstructural inspection was performed in the welding area and outside the weld for variant after only extrusion and for variant after extrusion and dynamic stretching before artificial ageing. It was revealed that the designed three-stage homogenization treatment led to dissolution of soluble phases present in the as-cast billets microstructure, which caused significant increase in solidus temperature, from 509 °C in as-cast state to 573 °C after completed soaking. The application of dynamic deformation during the straightening of aluminium profiles after hot extrusion with water cooling on the press run, led to the induced favourable changes in the microstructure of the alloy, which translated into a significant increase in UTS of about 11%.