Within the present work the homogenization of DC-cast (direct chill-cast) extrusion billets of Al-Mg-Si-Cu alloy was investigated. The alloy is characterized by higher Cu content than currently applied in 6xxx series. The aim of the work was analysis of billets homogenization conditions enabling maximum dissolution of soluble phases during heating and soaking as well as their re-precipitation during cooling in form of particles capable for rapid dissolution during subsequent processes. The material was subjected to laboratory homogenization and the microstructural effects were assessed on the basis of DSC (differential scanning calorimetry) tests, SEM/EDS (scanning electron microscopy/energy-dispersive spectroscopy) investigations and XRD (X-ray diffraction) analyses. The proposed homogenization scheme with three soaking stages enabled full dissolution of Q-Al₅Cu₂Mg₈Si₆ and θ-Al₂Cu phases. The β-Mg₂Si phase was not dissolved completely during soaking, but its amount was significantly reduced. Fast cooling from homogenization was needed to refine β-Mg₂Si phase particles, but despite this in the microstructure coarse Q-Al₅Cu₂Mg₈Si₆ phase particles were found. Thus, rapid billets heating may lead to incipient melting at the temperature of about 545 °C and the careful selection of billets preheating and extrusion conditions was found necessary.

Before artificial ageing, extruded aluminium profiles are subjected to stretching with a small cold deformation in the range of 0.5–2%. This deformation improves the geometrical stability of the extruded product and causes changes in the microstructure of the profile, which leads to the strain hardening of the material after artificial ageing. The work has resulted in the creation of the prototype of an original device, which is unique in the world, for the dynamic stretching of the extruded profiles after quenching. The semi-industrial unit is equipped with a hydraulic system for stretching and a pneumatic system for cold dynamic deformation. The aim of this research paper is to produce advantageous microstructural changes and increase the strength properties of the extruded material. The solution of the dynamic stretching of the profiles after extrusion is a great challenge and an innovation not yet practised. The paper presents the results of microstructural and mechanical investigations carried out on extruded AlMgSi(Cu) alloys quenched on the run-out table of the press, dynamically stretched under different conditions, and artificially aged for T5 temper. Different stretching conditions were applied: a static deformation of 0.5% at a speed of 0.02 m/s, and dynamic deformation of 0.25%, 0.5%, 1%, and 1.5% at speeds of 0.05 and 2 m/s. After the thermomechanical treatment of the profiles, microstructural observations were carried out using an optical microscope (OM) and a scanning electron microscope (SEM). A tensile test was also carried out on the specimens stretched under different conditions. In all the cases, the dynamically stretched profiles showed higher strength properties, especially those deformed at a higher speed of 2 m/s, where the increase in UTS was observed in the range of 7–18% compared to the classical (static) stretching. The microstructure of the dynamically stretched profiles is more homogeneous with a high proportion of fine dispersoids.

Extrusion welding of AlZnMg alloys encounters great technological difficulties in practice associated with high shaping forces and the low quality of longitudinal welds. Three different chemical compositions of 7021 aluminum alloy, differing in terms of Zn and Mg contents, were used in the first stage of the research. The laboratory device modelling the behavior of metal in welding chambers of the porthole die was applied to examine the ability of 7021 alloys to produce high-quality joints. The weldability tests were carried out for different welding temperatures—400, 450 and 500 °C—and for a fixed welding pressure of 300 MPa. The microstructural effects in pressure-welds were evaluated with the use of OM and SEM/EDS. The temperature–pressure parameters in the welding chambers were analyzed by using the FEM method for original porthole dies while extruding tubes with dimensions of Ø50 × 2 mm. Finally, the industrial extrusion trials were performed with examination of the structure and strength of the seam welds. It was found that it is possible to produce high-quality high-strength welds in tubes extruded from AlZnMg alloys in industrial conditions (the strength of welds in the range of 96–101% of the strength of the basic non-welded material) through properly matched alloy chemical composition of the alloy, construction of the porthole dies and temperature–speed conditions of deformation.

In the realm of modern architecture, the demand for materials that combine strength, durability, and aesthetic flexibility is ever-growing. Addressing this need, this paper presents a study on the innovative use of aluminum extrudates in construction. Focusing on the AA6005 alloy, which is known for its excellent balance of strength, corrosion resistance, and weldability, this research delves into the development of an extrusion process that yields thin-walled, lightweight, yet high-strength structural components. Using FEM simulations, a new extrudate of the AA6005A was developed. It is compatible with standard façade systems, with high-strength properties and a weight reduced by 20% compared to that of conventional extrudates made of the AA6063 alloy. Using CAD engineering and FEM simulations of aluminum extrusion process, an innovative die was designed for the extrusion process, ensuring uniform flow of metal from the bearing and minimizing the elastic deflection of the die. This resulted in an increase in the extrusion velocity of thin-walled extrudate from AA6005A by 24% compared to conventional profiles extruded from AA6063. As part of the research, a trial test was carried out in production conditions and the quality of the extrudates was tested by 3D optical scanning, mechanical and structural properties tests, and microstructure observation.

In the first part of the work, the 3-step homogenization procedure was carried out for AlMgSi(Cu) alloy, aimed at obtaining billets microstructure with numerous fine particles of strengthening phases and increased solidus temperature. In the second part of the work, an original on a global scale prototype device for the dynamic stretching of extruded profiles before artificial ageing, was proposed and tested in semi-industrial conditions. The thermo-mechanical treatment of extruded hollow profiles from AlMgSi(Cu) alloy with 1.22% content of copper was performed with dynamic deformation range: 0.25%, 0.5%, 1%, 1.5% and 2%. The microstructural inspection was performed in the welding area and outside the weld for variant after only extrusion and for variant after extrusion and dynamic stretching before artificial ageing. It was revealed that the designed three-stage homogenization treatment led to dissolution of soluble phases present in the as-cast billets microstructure, which caused significant increase in solidus temperature, from 509 °C in as-cast state to 573 °C after completed soaking. The application of dynamic deformation during the straightening of aluminium profiles after hot extrusion with water cooling on the press run, led to the induced favourable changes in the microstructure of the alloy, which translated into a significant increase in UTS of about 11%.

In this paper, dedicated material models were developed and verified for three melts of EN AW-7021 alloy, differing in zinc and magnesium content, for tube extrusion conditions. Based on the plastometric tests, it was found that in the studied range of strain parameters, the analyzed melts of the same aluminum alloy showed different sensitivity to strain rate and temperature. In addition, a significant effect of magnesium and zinc content on the plasticity of the tested material was observed. Therefore, dedicated material models describing stress changes were developed for each melt analyzed. The models were then implemented into the material database of the QForm-Extrusion^® program, which was used for the theoretical analysis of the industrial extrusion process. In order to verify the results of numerical calculations, industrial tests of the extrusion process were carried out. The force parameters and the rate of the extrusion process were mainly analyzed. The use of dedicated material models for each melt contributed to the accuracy of numerical modeling. A high degree of compliance was obtained regarding the theoretical and experimental extrusion force and the velocity of metal flowing out of the die cavity, among others.