Environmentally sustainable cement mortars containing wheat straw (Southern Italy, Apulia region) of different length and dosage and perlite beads as aggregates were prepared and characterised by rheological, thermal, acoustic, mechanical, optical and microstructural tests. A complete replacement of the conventional sand was carried out. Composites with bare straw (S), perlite (P), and with a mixture of inorganic and organic aggregates (P/S), were characterised and compared with the properties of conventional sand mortar. It was observed that the straw fresh composites showed a decrease in workability with fibre length decrease and with increase in straw volume, while the conglomerates with bare perlite, and with the aggregate mixture, showed similar consistency to the control. The thermal insulation of the straw mortars was extremely high compared to the sand reference (85–90%), as was the acoustic absorption, especially in the 500–1000 Hz range. These results were attributed to the high porosity of these composites and showed enhancement of these properties with decrease in straw length and increase in straw volume. The bare perlite sample showed the lowest thermal insulation and acoustic absorption, being less porous than the former composites, while intermediate values were obtained with the P/S samples. The mechanical performance of the straw composites increased with length of the fibres and decreased with fibre dosage. The addition of expanded perlite to the mixture produced mortars with an improvement in mechanical strength and negligible modification of thermal properties. Straw mortars showed discrete cracks after failure, without separation of the two parts of the specimens, due to the aggregate tensile strength which influenced the impact compression tests. Preliminary observations of the stability of the mortars showed that, more than one year from preparation, the conglomerates did not show detectable signs of degradation.

Contaminated sediments may induce long-term risks to humans and ecosystems due to the accumulation of priority and emerging inorganic and organic pollutants having toxic and bio-accumulation properties that could become a secondary pollution source. This study focused on the screening of novel bio-based materials to be used in the decontamination of marine sediments considering technical and environmental criteria. It aimed to compare the environmental impacts of cellulose-based adsorbents produced at lab scale by using different syntheses protocols that involved cellulose functionalization by oxidation and branching, followed by structuring of an aerogel-like material via Soxhlet extraction and freeze-drying or their combination. As model pollutants, we used 4-nitrobenzaldehyde, 4-nitrophenol, methylene blue, and two heavy metals, i.e., cadmium and chromium. When comparing the three materials obtained by only employing the Soxhlet extractor with different solvents (without freeze-dying), it was observed that the material obtained with methanol did not have a good structure and was rigid and more compact than the others. A Life Cycle Assessment (LCA) was conducted to evaluate the environmental performance of the novel materials. Apart from the hierarchical categorization of the materials based on their technical and environmental performance in eliminating organic pollutants and heavy metal ions, it was demonstrated that the cellulose-based material obtained via Soxhlet extraction with ethanol was a better choice, since it had lower environmental impacts and highest adsorption capacity for the model pollutants. LCA is a useful tool to optimize the sustainability of sorbent materials alongside lab-scale experiments and confirms that the right direction to produce new performant and sustainable adsorbent materials involves not only choosing wastes as starting materials, but also optimizing the consumption of electricity used for the production processes. The main results also highlight the need for precise data in LCA studies based on lab-scale processes and the potential for small-scale optimization to reduce the environmental impacts.

Pyrolysis of plastic from waste electrical and electronic equipment (WEEE) is a promising method for producing value-added chemicals. However, flame retardants in WEEE can cause halogen contamination in pyrolysis oil, reducing its value. This work aims to develop an innovative catalytic hydrodehalogenation (CHD) protocol for the removal of chlorobenzene and bromobenzene. Iron sulphate heptahydrate (FeSO₄·7H₂O) and nickel ammonium sulphate hexahydrate ((NH₄)₂Ni(SO₄)₂·6H₂O) were used as catalysts, while sodium borohydride (NaBH₄) acted as a hydrogen donor for iron reduction. The novelty of the process lies in the generation of nano zero-valent iron (nZVI) that takes place within the CHD reactor (in situ) without the addition of strong acids. Various experimental set-ups were investigated to optimise the key process parameters (e.g., reagent concentrations). The optimal conditions—obtained in the autoclave at 30 °C with a 1:1 molar ratio of chlorobenzene to catalyst, omission of nickel salt, and 5 mmol of NaBH₄—resulted in a 75% reduction in chlorobenzene and complete removal of bromobenzene. The results confirm the effectiveness of the proposed protocol for the dehalogenation of chlorobenzene and bromobenzene, which can facilitate the valorization of pyrolysis oils derived from plastic waste, contributing to the closure of the WEEE cycle (the widest and fastest-growing source of global waste with significant environmental, social and economic impacts).

Bio-based adsorbent materials represent a sustainable alternative for the remediation of contaminated environments. In this work, two lightweight porous sponges derived from cellulose and chitin and functionalized with branched polyethylenimine were synthesized and comparatively investigated as adsorbents for organic compounds and heavy metals. The chitin-based material was obtained by adapting a synthetic platform originally developed for cellulose, demonstrating the transferability of the approach to a structurally distinct biopolymer derived from seafood-industry waste. Adsorbents were characterized by spectroscopy, scanning electron microscopy, and thermogravimetric analysis, confirming successful oxidation and polyethylenimine grafting as well as the formation of highly porous structures. Adsorption experiments with 4-nitrophenol, 4-nitrobenzaldehyde, methylene blue, and eosin B revealed comparable performance for both adsorbents, with adsorption strongly influenced by dye structure, pH, and speciation. Both materials exhibited efficient removal of 4-nitrobenzaldehyde and eosin B in deionized (>95%) and marine water (>75%); whereas 4-nitrophenol and methylene blue were only moderately adsorbed (<40%). Tests with inorganic contaminants (cadmium and chromium) showed maximum experimental Cd(II) uptakes of 38.88 mg/g for the cellulose- and 43.21 mg/g for the chitin-based material. Overall, surface functionalization dominates adsorption behavior over the polysaccharide backbone, identifying chitin-based material as a promising, sustainable adsorbent for environmental remediation.