To improve the accuracy of atmospheric visibility (V) prediction based on machine learning in different pollution scenarios, a new atmospheric visibility prediction method based on the stacking fusion model (VSFM) is established in this paper. The new method uses the stacking strategy to fuse two base learners—eXtreme gradient boosting (XGBoost) and light gradient boosting machine (LightGBM)—to optimize prediction accuracy. Furthermore, seasonal feature importance evaluations and feature selection were utilized to optimize prediction accuracy in different seasons with different pollution sources. The new VSFM was applied to 1-year environmental and meteorological data measured in Qingdao, China. Compared to other traditional non-stacking models, the new VSFM improved precision during different seasons, especially in extremely low-visibility scenarios (V< 2 km). The TS score of the VSFM was significantly better than that of other models. For extremely low-visibility scenarios, the VSFM had a threat score (TS) of 0.5, while the best performance of other models was less than 0.27. The new method is promising for atmospheric visibility prediction under complex urban pollution conditions. The research results can also improve our understanding of the factors that influence urban visibility.

The aerosol hygroscopic growth (HG) characteristics in coastal areas are very complex, which is one of the main influences on the simulation accuracy of radiation transfer modeling for coastal environments. Previous studies have shown that aerosol HG characteristics are very different in open oceans and inland regions. However, the aerosol HG features in coastal areas are strongly affected by its type. In this work, an aerosol backward trajectory tracing model was used to classify the local aerosol type. Using long-term field campaign data in Qingdao (25 September 2019 to 25 October 2020), the HG characteristics of different types of aerosols (i.e., land source, sea source, and mixed aerosol) under different seasons and different atmospheric environments (i.e., pollution background and clean background) were studied. Quantitative models of aerosol HG factor were established for aerosols from different sources in different seasons and under different pollution background conditions. The major type of local aerosol is terrestrial aerosol, as the marine source only accounts for 10–20%. Seasonal HG characteristics (deliquescence point, DP) of mixed and land source aerosol vary significantly, from around RH = 60% to RH = 85%, while that of the marine aerosol is rather consistent (RH = 80%). When the atmospheric background is relatively clean, the DPs of aerosols from different sources are almost the same (about RH = 80%), but when the pollution is heavy, the DPs of terrestrial aerosols are almost 20% lower than those of marine sources. These models can be directly used to characterize the hygroscopic characteristics of atmospheric aerosols in Qingdao at specific seasons or pollution levels for radiative transfer modeling, remote sensing, and so forth.

Understanding optical turbulence within the atmospheric boundary layer (ABL) is essential for refining atmospheric motion analyses, enhancing numerical weather prediction models, and improving light propagation assessments. This study develops an optical turbulence model for the boundary layer over the South China Sea (SCS) by integrating multiple observational and reanalysis datasets, including ERA5 data from the European Center for Medium-Range Weather Forecasts (ECMWF), radiosonde observations, coherent Doppler wind lidar (CDWL), and ultrasonic anemometer (CSAT3) measurements. Utilizing Monin–Obukhov Similarity Theory (MOST) as the theoretical foundation, the model’s performance is evaluated by comparing its outputs with the observed diurnal cycle of near-surface optical turbulence. Error analysis indicates a root mean square error (RMSE) of less than 1 and a correlation coefficient exceeding 0.6, validating the model’s predictive capability. Moreover, this study demonstrates the feasibility of employing ERA5-derived temperature and pressure profiles as alternative inputs for optical turbulence modeling while leveraging CDWL’s high-resolution observational capacity for all-weather turbulence characterization. A comprehensive statistical analysis of the atmospheric refractive index structure constant ($C_n^2$) from November 2019 to September 2020 highlights its critical implications for optoelectronic system optimization and astronomical observatory site selection in the SCS region.

Analysis of turbulent heat fluxes in urban forests is crucial for understanding structural variations in the urban sub-surface boundary layer. This study used data captured by an unmanned aerial vehicle (UAV) and an improved semi-empirical triangle method to estimate small-scale turbulent heat fluxes in the sub-surface of an urban forest. To improve the estimation accuracy, the surface temperature (T_S) of the UAV-based remote sensing inversion was corrected using the hot and cold spot correction method, and the process of calculating ${\varphi }_{max}$ using the traditional semi-empirical triangle method was improved to simplify the calculation process and reduce the number of parameters in the model. Based on this method, latent heat fluxes (LE) and sensible heat fluxes (H) were obtained with a horizontal resolution of 0.13 m at different time points in the study area. A comparison and validation with the measured values of the eddy covariance (EC) system showed that the absolute error of the LE estimates ranged from 4.43 to 23.11 W/m², the relative error ranged from 4.57% to 25.33%, the correlation coefficient (r) with the measured values was 0.95, and the root mean square error (RMSE) was 35.96 W/m², while the absolute error of the H estimates ranged from 3.42 to 15.45 W/m², the relative error ranged from 7.51% to 28.65%, r was 0.91, and RMSE was 9.77 W/m². Compared to the traditional triangle method, the r of LE was improved by 0.04, while that of H was improved by 0.06, and the improved triangle method was more accurate in estimating the heat fluxes of urban mixed forest ecosystems in the region. Using this method, it was possible to accurately track the LE and H of individual trees at the leaf level.