Boris Buravov

Dr. Boris Buravov

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 November 2022 in Fine Chemical Technologies
Verified
Journal Article
Open access
PDF file
BBBoris Buravov
Boris Buravov
AAAli Khudhair Jabbar AL-HAMZAWI
Ali Khudhair Jabbar AL-HAMZAWI
EBE. S. Bochkarev
E. S. Bochkarev
NGN. Kh. Grichishkina
N. Kh. Grichishkina
SBSergey Vladimirovich Borisov
Sergey Vladimirovich Borisov
OTO. O. Tuzhikov
O. O. Tuzhikov
Objectives. To synthesize phosphorus-containing oligoestermethacrylates spatially separated by spacers of aliphatic or aromatic structure and evaluate their effect on photocuring kinetics.Methods. For determining the qualitative and quantitative composition of the synthesized compounds, the following methods were used: thin layer chromatography; chromatographic and mass spectrometry; infrared spectroscopy; 1H, 13C, 31P nuclear magnetic resonance spectroscopy; differential scanning calorimetry. The dielectric loss tangent was determined on a specially designed optical cell with an ultraviolet (UV) light source to an immittance meter. Elemental analysis was performed on an energy dispersive X-ray fluorescence spectrometer.Results. Spatially separated oligoestermethacrylates based on phosphorus trichloride containing aliphatic or aromatic spacers in the structure were synthesized. During the interaction of glycidyl methacrylate with phosphorus trichloride in the mass of the latter, reaction products were shown to be formed both according to the Krasusky rule from the side of the α-carbon atom, as well as against this rule with the formation of isomeric products. Obtaining these compounds in bulk is possible only in the presence of a homopolymerization inhibitor. The influence of the spacer structure on the curing rate of oligoestermethacrylates under the action of UV radiation has been established. It has been shown that the introduction of a spacer into the oligomer structure is accompanied by an increase in the induction period by a factor of 39 compared to a sample without a spacer.Conclusions. The results obtained indicate the possibility of obtaining new oligoestermethacrylates with aliphatic and aromatic spacers in the structure. The influence of the structure of the spacer on the kinetics of photocuring is determined.

18 August 2024 in Polymers
Verified
Journal Article
Open access
PDF file
STStanislav Trubachev
Stanislav Trubachev
APAlexander A. Paletsky
Alexander A. Paletsky
ESEgor Alexandrovich Sosnin
Egor Alexandrovich Sosnin
OTOleg O. Tuzhikov
Oleg O. Tuzhikov
BBBoris Buravov
Boris Buravov
Xin WangXin Wang
Xin Wang
This paper presents a study of the flammability and thermal decomposition products of glass fiber-reinforced epoxy resin (GFRER) with the addition of cardanol-based phosphorus-containing benzoxazine monomer (CBz) and graphene and their combinations in different proportions (up to 20 wt.%). The addition of CBz alone or in combination with graphene resulted in an increase in the limiting oxygen index (LOI) and self-extinguishing in the UL-94 HB test. The flame-retardant samples had better tensile mechanical properties than the sample without additives. The differential mass-spectrometric thermal analysis (DMSTA) of the thermal decomposition products of GFRER without additives and with the addition of CBz and graphene was carried out. CBz addition promoted the thermal decomposition of high-molecular-weight products of epoxy resin decomposition in the condensed phase and at the same time decreased the time of release of low-molecular-weight thermal decomposition products into the gas phase. Graphene addition resulted in an increase in the relative intensities of high-molecular-mass peaks compared to GFRER without additives.

14 January 2026 in Fine Chemical Technologies
Verified
Journal Article
Open access
PDF file
BBBoris Buravov
Boris Buravov
AAAli Khudhair Jabbar AL-HAMZAWI
Ali Khudhair Jabbar AL-HAMZAWI
RGR. B. Gadzhiev
R. B. Gadzhiev
SOS. A. Orlova
S. A. Orlova
LDL. Yu. Donetskova
L. Yu. Donetskova
OTOleg O. Tuzhikov
Oleg O. Tuzhikov
Objectives. The work sets out to investigate the influence of the structure of spacer in structure of phosphorus(III)-containing oligoester(meth)acrylates on physical and mechanical properties of polymers and their combustibility. Methods. The physical and mechanical properties of polymers were determined using the following: DMA 242 E Artemis dynamic mechanical analyzer ( NETZSCH , Germany); universal testing machine for standard tests on materials ( ZwickRoell Group , Germany); GT-7045-HMH(L) impact test machine ( Gotech Testing Machines, Inc ., Taiwan); Q-1500 D derivatograph of the Paulic–Paulic– Erdey system (thermogravimetry, IOM , Hungary); Oxygen Index Module device for determination of burning behavior by plastic flammability testing according to oxygen index ( Concept Equipment , United Kingdom); GT-7045-HMH(L) device for determination of the Vicat softening temperature ( Gotech Testing Machines, Inc ., Taiwan); SFT-110XW supercritical fluid extractor ( Supercritical Fluid Technologies, Inc ., USA) for supercritical fluid extraction with carbon dioxide. Results. The influence of the spacer structure in the structure of phosphorus(III)-containing oligoester(meth)acrylates on the dynamic mechanical and physicomechanical properties of polymers was established. Comparative assessment of the impact of the spacer structure on properties of polymers was carried out in terms of their heat stability (thermogravimetric analysis) and combustibility (measurement of limited oxygen index). It is established that polymers having balanced physical and mechanical properties can be obtained by introducing spacer characteristics into the oligomer structure. Polymers obtained on the basis of phosphorus(III)-containing oligoester(meth)acrylates with spacers demonstrate considerable resistance to impact strength tests. Conclusions. The achieved results testify to the possibility of obtaining polymers on the basis of phosphorus(III)-containing oligoester(meth)acrylates with spacer attributes that possess increased resistance to impact strength and thermal stability tests at an insignificant decrease in their combustibility.

4 November 2024 in Fine Chemical Technologies
Verified
Journal Article
Open access
PDF file
LDL. Yu. Donetskova
L. Yu. Donetskova
SSS. M. Solomakhin
S. M. Solomakhin
ANA. V. Nalesnaya
A. V. Nalesnaya
AAAli Khudhair Jabbar AL-HAMZAWI
Ali Khudhair Jabbar AL-HAMZAWI
BBBoris Buravov
Boris Buravov
OTOleg O. Tuzhikov
Oleg O. Tuzhikov
Objectives. To obtain polymer composite materials (PCM) with enhanced physicomechanical properties using the vacuum assisted resin transfer molding (VaRTM) method, binders must have a viscosity of up to 500 mPa∙s. In some cases, this leads to restrictions on the use of certain materials or requires the use of temporary diluents. This is closely related to the deterioration of other required composite characteristics, such as increased flammability. Three phosphorus-containing oligoester(meth)acrylates PhOEM-1, PhOEM-2, and PhOEM-3 were synthesized with significant differences in viscosity characteristics in the series PhOEM-1 << PhOEM-2 << PhOEM-3. The polymer based on PhOEM-1 exhibits inferior physicomechanical properties despite having lower viscosity. Hence, the aim of the study was to investigate the viscosity characteristics of mixtures of methacrylate binders of the same nature but different structures and functionalities. This was done by studying the rheological properties of the original oligoester(meth)acrylates and their mixtures taken in various ratios. The method used was to optimize compositions via a simplex lattice (Scheffe’s plan), in order to obtain PCM using the VaRTM technology.Methods. The study of rheological properties of phosphorus-containing oligoester(meth)acrylates and their mixtures was conducted using the method of rotational viscometry on a Brookfield LVDV-II + Pro viscometer with a spindle 27 at different shear rates ranging from 0 to 70 s−1 and temperatures from 30 to 70°C. Rheological studies were also conducted on a Lamy Rheology GT300 PLUS (GEL TIMER) viscometer in the same range of shear rates and temperatures.Results. It was established that the objects under investigation can be characterized by viscosity values ranging from 96 to 2137 mPa∙s depending on the temperature. The nature of the viscous flow of phosphorus-containing oligoester(meth)acrylates and their mixtures is similar to that of Newtonian liquids only at certain shear rates. The effective activation energies of the viscous flow of binders and their mixtures were calculated, and the influence of temperature on the viscosity of binders was determined.Conclusions. The study identified the features and nature of the flow curves of phosphorus-containing oligoester(meth)acrylate binders of the same nature but different structures and functionalities, as well as of their mixtures. The optimal composition ranges of threecomponent mixtures of phosphorus-containing oligoester(meth)acrylates for use in the VaRTM technological process in producing polymer composite materials within the temperature range of 30 to 70°C were defined. The optimal compositions and temperature conditions for obtaining polymer composite materials using the VaRTM technology were also identified. This enables the production of polymer products with complex geometric shapes and varying sizes.

22 May 2026 in Polymer Composites
Verified
Journal Article
Closed access
YKYu. N. Kamenev
Yu. N. Kamenev
SBSergey Vladimirovich Borisov
Sergey Vladimirovich Borisov
BBBoris Buravov
Boris Buravov
VKVladimir G. Kochetkov
Vladimir G. Kochetkov
MRM. A. Rogozhkina
M. A. Rogozhkina
MVM. A. Vaniev
M. A. Vaniev

11 December 2025 in Polymers
Verified
Journal Article
Open access
PDF file
SBSergey Vladimirovich Borisov
Sergey Vladimirovich Borisov
BBBoris Buravov
Boris Buravov
DKDaria Andreevna Kudryavtseva
Daria Andreevna Kudryavtseva
VKValentin Kharlamov
Valentin Kharlamov
AKArtem Aleksandrovich Kobelev
Artem Aleksandrovich Kobelev
INIvan Aleksandrovich Novakov
Ivan Aleksandrovich Novakov
This study addresses the drawbacks of traditional dispersed fire retardants—such as anisotropy, reduced strength, and poor filler impregnability—by developing in situ-formed hybrid epoxy composites. The materials, based on diglycidyl ether of bisphenol A and triethylenetetramine, were modified with a solution of zinc sulfate heptahydrate in orthophosphoric acid. This approach yielded near-spherical microparticles (6–16 µm) within the polymer matrix. The scientific novelty lies in investigating how such in situ particle formation affects material properties. The modification significantly enhanced fire resistance: char residue increased 1.7–2.2-fold, while total heat release, peak heat release rate, and smoke release were reduced by up to 60.5%, 40.2%, and 70%, respectively. The observed increase in the mass loss rate suggests that accelerated thermal-oxidative degradation promotes char formation. These findings, supported by scanning electron microscopy, energy-dispersive X-ray spectroscopy, and Fourier-transform infrared spectroscopy data, demonstrate the efficacy of the in situ strategy for creating high-performance, fire-safe epoxy composites.