In this article, the four-switch buck–boost (FSBB) converter is a preferred choice for the dc–dc applications where the step-up and step-down are needed. In order to reduce the inductor size and improve the efficiency, the zero-voltage switch (ZVS) control schemes with four segments inductor current for FSBB have been investigated in numerous publications. Among these ZVS control schemes, the optimized control variable stored as the huge look-up table data achieved minimum root-mean-square (RMS) inductor current, and the complex real-time calculation is avoided. However, for the purpose of matching the wide input and output voltage ranges, an external flash is needed for storing the look-up table data; And the large time consumption for invoking the data hazard the dynamic performance significantly. To reduce the storage device cost and meet the demand of transient, a simplified real-time control algorithm is proposed by dividing the operation into the defined Discontinuous Conduction Mode (DCM) and Continuous Conduction Mode (CCM) operation featuring the minimum RMS inductor current and ZVS operation during the whole voltage range without complex calculation and mode transient. Finally, a 300 W dc–dc prototype is built to verify the theoretical analysis and proposed control scheme with a low-cost real-time digital controller.
13 July 2021 in IEEE Transactions on Power Electronics
The resonant dc–dc converter is preferred for high-efficiency applications due to its less switching loss and better electromagnetic interference (EMI) characteristics. However, in a wide range of steady-state voltage gain applications, such as the on-board charger application, the wide output voltage range will lead to a bulky resonant inductor, which will decrease the power density. Magnetic integration of the inductor and transformer is an effective way to reduce the total magnetic volume. However, the traditional integrated magnetics of transformer and inductor will result in high magnetic field intensity in the external space nearby the integrated magnetic component. This external magnetic field will cause large eddy current losses in the neighboring metal heatsink and serious EMI issues. In order to deal with this problem, an integrated winding structure with a negligible external magnetic field is proposed in this article. By rebuilding the external winding segments with a better coupling coefficient, the external magnetic field intensity is canceled without efficiency and size sacrifices. Detailed analysis and design procedures of the proposed structure are presented. A 6.6-kW dc–dc prototype is built to verify the cancelation effect of the magnetic field intensity in the neighboring external space.
23 October 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Magnetic integration effectively reduces the total magnetic volume for a converter with multiple magnetic components. However, the existing integrated inductor and transformer still face some problems, such as a large core cross-sectional area due to the small effective inductor winding number or low PCB utilization due to unreasonable winding structure design. A new inductor and transformer integrated magnetic structure with high PCB utilization and a small core volume for the resonant converter is proposed in this paper. The integrated resonant inductor is constructed by both the primary and secondary side windings, which increases not only the effective inductor turn number but also the utilization of the PCB. What’s more, the core plates of the inductor and the transformer are integrated to furtherly increase the utilization of the core. The design methodology for the proposed integrated magnetics (IM) is also given in this paper. Finally, the proposed integrated magnetics and design methodology are verified on a 2kW CLLC prototype. Compared with the discrete magnetic components, the integrated magnetics volume is reduced by about 25% with a similar loss.
18 July 2023 in IEEE Transactions on Power Electronics
A resonant four-switch inverting buck-boost converter is a good choice for DC/DC applications that require an inverting voltage solution. A soft switching control scheme with four segments of resonance current has been examined using duty ratio and phase shift as control variables. As a result, the RMS value of the resonance current is low compared to DCM, which is directly proportional to the conduction loss. This control scheme allows the converter to regulate its output voltages more efficiently with soft switching operations. Thus, it contributes to an increment in efficiency improvement and board size reduction. At the same time, a simple close-loop is designed to meet the requirement of a wide voltage range with the corresponding simplified real-time PI control algorithm. For the verification of the proposed control scheme, a resonant four-switch inverting buck-boost DC/DC converter is designed and experimentally tested, which has recorded over 98.5% peak efficiency at a 1:1 inverting case (-48Vdc to 48Vdc). The converter's wide operating range is from -48Vdc to 28ni Vdc ∼ 60Vdc output voltage with a power density of 500W/in3.
In traditional inductor design with planar windings, the magnetic field distribution may not be well-organized, leading to significant winding loss, particularly at high switching frequencies. This study explores the relationship between current distribution and magnetic field distribution in the winding region. Unlike conventional magnetic flux distribution, which directs a large portion of the magnetic field vertically through the windings in the winding region, this work introduces a structure that maintains most of the magnetic flux parallel to the foil windings through the application of quasi-distributed air gaps. This paper presents a design methodology for a high-frequency foil winding inductor with high flux variation. Building on this concept, a high-power density, low loss inductor with foil windings is designed based on the four-switch buck-boost (FSBB) converter. Experimental results demonstrate that the proposed inductor design significantly reduces winding loss in inductors with planar windings.
20 January 2025 in Journal of Electrical Engineering & Technology