Red mud (RM) is a waste material obtained during the production of aluminum from bauxite minerals. RM causes environmental pollution due to its high alkaline properties. Therefore, RM materials are stored in waste reservoirs. As production continues, the number of required waste reservoirs increases day by day. This study aims to utilize RM waste material in construction structures to contribute to the economy. The research investigates the potential use of RM waste material as road fill material. RM was improved using another waste material of fly ash (FA) since RM has low strength. Atterberg limit tests, compaction tests, unconfined compression tests, CBR tests, and SEM analyses were conducted on stabilized RM samples. In the physical properties of stabilized RM, Atterberg limits and optimum moisture content increase and density decreases since FA content increases. In the mechanical properties of stabilized RM, unconfined compressive strength, initial and secant modulus of elasticity, and California bearing ratio increase and maximum peak strain decreases since FA content and curing period increase. SEM images prove the increase in mechanical properties due to the cementation products (CSH and CAH gels) formed in the microstructure of stabilized RM. The results showed that RM waste stabilized with FA can be used as road subgrade material.
This study provides a comprehensive evaluation of red mud as a sustainable material for road base construction, particularly in combination with bottom ash. Red mud, a by-product of the Bayer process used in alumina extraction, is known for its high alkalinity and heavy metal content. For this reason, this waste material causes environmental challenges. Red mud sourced from the Eti Aluminum Factory in Seydişehir, Konya (Turkey), was stabilized with bottom ash. Then, these waste materials were tested through a number of experiments, such as in relation to their Atterberg limits, compaction characteristics, unconfined compressive strength (UCS), California bearing ratio (CBR), and microstructure through a scanning electron microscopy (SEM) analysis. The results highlight that the UCS of stabilized red mud samples significantly improved with the addition of bottom ash and longer curing periods. Specifically, the UCS values increased from 0.5 MPa to 2.5 MPa after 28 days of curing. Moreover, RM specimens stabilized with 25% bottom ash achieved a CBR value of 146.64% after 28 days, far exceeding Turkey’s road fill material requirement, which mandates a minimum unsoaked CBR value of 15%. These findings indicate that red mud stabilized with bottom ash not only meets but exceeds the structural requirements for road base materials. This approach provides a sustainable solution for the environmental management of red mud while contributing to infrastructure development. Through the recycling of these industrial by-products, this study presents a viable method to reduce waste and support economic and environmental sustainability in road construction projects.
10 September 2022 in Arabian Journal of Geosciences
Filter sludge (FS) is a waste material that occurs during sugar production in the sugar industry, and since it is not used anywhere, it creates a problem due to storage costs and environmental damage. In the present study, high plasticity clay was stabilized with a filter sludge which has never been used for soil stabilization in field cases. The changes in the geotechnical properties of a high plasticity clay (CH) with the additive of filter sludge (FS) were investigated. The amount of FS mixed into CH soil is 3-6-9-12-15% by dry weight of the soil. Changes in geotechnical properties such as consistency limits, compaction parameters, strength, swelling potential, CBR value of improved soils were determined. The plastic limit and optimum water content increase as the FS content added to the soil increases; liquid limit, plasticity index, and maximum dry density decrease. Improved soil strength increases as the curing time and FS amount increase, and the highest strength was obtained with 15% of FS. At the optimum additive ratio, the unconfined compressive strength increases by 33%. The swelling percentage of CH clay decreases from 42.5% to 20%. According to the wet CBR test results, the bearing capacity of the improved soil increased from %1.1 to %4.4. As a result of this study, it was seen that the FS waste material improved the geotechnical properties of the soil.
1 January 2023 in Turkish Journal of Civil Engineering
The lime column (LC) technique has been commonly used for the improvement of expansive soils. The achievement of this technique depends on the lime diffusion into the expansive soils, but lime diffusion into the expansive soil is generally a slow process due to the low permeability of these soils. In this study, sodium lignosulfonate, which is used as a superplasticizer in the concrete industry, was added to lime columns to accelerate the diffusion of lime particles. First, treated expansive clay specimens with thirty-seven 4.5 mm diameter columns were prepared in an oedometer ring. These columns were filled with two different mixtures: water-lime and water-lime-sodium lignosulphonate to investigate the effect of the addition of sodium lignosulphonate. Free swell tests were done on these treated expansive clay specimens that were subjected to different curing periods, it was observed that the treated specimens with sodium lignosulphonate lime columns (NaLS-LC) are more effective than the treated specimens with lime columns (LC). A treated expansive clay specimen (in a 30cmx30cm mold) with seven pieces of 45 mm diameter sodium lignosulphonate lime columns were prepared to observe the alteration of engineering properties of untreated expansive clay specimen (US) located between the columns. Free swell and unconfined compressive strength tests were done on the undisturbed expansive clay specimens taken from the mold between the columns. SEM-EDX analyses were made to investigate whether the ettringite mineral, which leads to swelling of the expansive soil during lime stabilization, forms or not. While the ettringite mineral formed during the curing period in the lime column stabilization method, the addition of sodium lignosulphonate to lime columns blocked the formation of the ettringite mineral. It can be stated that sodium lignosulphonate lime columns (NaLS-LC) show better performance than lime columns (LC), in the treatment of expansive clays.
21 August 2023 in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
The settlements occurred in building foundations depend on many soil parameters. Thus, these parameters make the solution both difficult and complex during the calculating process. Therefore, finite element programs use the subgrade reaction coefficient to facilitate the foundation solution. Two different methods, which are Winkler method and Pseudo coupled method, are used in the basic solutions with the coefficient of subgrade reaction. While the Winkler method can be solved with a single field, the pseudo method can be solved with 2 or more fields. In this study, a 10 story building with a 36 m x 36 m square foundation was separately designed on four different sand soils. Two of these soils are classified as C and the others are classified as D according to Eurocode 8. The foundation of this building built on four different soils was divided into six different areas (one region, two regions, three regions, five regions, seven regions, 10 regions). Consequently, 24 pieces analyzes were solved with ETABS programs. One of the results from these analyzes is that Winkler method is suitable for the rigid foundation. In addition, since the settlements occurred at raft foundations are small, it has been observed that both Winkler and Pseudo-coupled method are suitable for rigid foundation acceptance. Pseudo-coupled method has generally been found to be a suitable method for flexible raft foundation. In the Pseudo-coupled method, the highest settlements were obtained in the two-region solutions. An optimum number of fields was found to be 7 for Pseudo-coupled method.