The purpose of this study is to generate some experimental data associated with the thermal heat exchange between an oil jet flow and a rotating gear. To this end, a specific test bench was designed. The principle of this test bench is to inject oil heated to a temperature of about 80 °C onto a rotating test sample at ambient temperature. Temperature measurements of the oil via injection nozzles and the rotating component allow the determination of the heat flow between these elements using a numerical method developed to this end. This test rig enables the study of the parameters that may affect heat exchange, such as oil flow rate and injection temperature, nozzle geometry and position, gear rotational speed and tooth geometry, or oil characteristics. In this study, three of these parameters were investigated, namely the test sample rotational speed, the oil flow rate, and the oil jet velocity. The experiments were conducted on an aluminum disc and spur gear. Subsequently, the experimental results were compared with existing models that represent the convective exchanges between oil and a gear. Some discrepancies between existing models and experimental results appear at high rotational speeds, underlining that the convective heat transfer does not always increase with this parameter.
26 October 2021 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Accurate modelling of friction coefficient is of primary importance in efficiency, vibration and failure analyses of enclosed gear drives. After showing the influence of surface/lubricant interactions on friction, the authors used a semi-empirical model which can take all these aspects into account. Lubricant is modelled as an Eyring–Reynolds fluid and rough surfaces are described with two parameters via a stochastic approach. A specific two-disc machine is used to perform series of friction measurements on smooth and rough discs. Smooth discs allow to operate under full film lubrication and to measure a reference shear stress of lubricant, whereas rough discs reproduce gear tooth roughness and generate a representative value of friction on asperities. The purpose of this present paper is to describe calculations of this physical-based friction coefficient model and to present the experimental process. On the basis of new results, the impact of a surface finishing process is assessed as well as the consequence of calculating friction coefficient based on oil injection instead of local bulk temperature.
This study presents a theoretical and experimental analysis to quantify the power losses generated by an oil jet lubricated angular contact ball bearing. The analysis is conducted for a moderate speed range (N∙dm product less than ) and a limited applied load (<5% of the static capacity). The lubrication regime of each ball is studied through a theoretical model and varies from Iso-Viscous Rigid to Elasto-Hydrodynamic. Therefore, the hydrodynamic effects are considered in the power loss calculation. An experimental campaign is carried out and the influence of several parameters (applied load, oil injection temperature, speed, etc.) is studied. A good agreement is found between the developed model and the measurements. It is shown that the radial applied load has no influence on power losses, unlike speed and axial load. This can be explained by the load distribution and the hydrodynamic rolling contribution on the low loaded balls.
13 December 2022 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Due to their properties, ceramic materials can improve both reliability and efficiency of rolling bearings. Most of the studies have investigated the power losses and temperatures of ball bearings with balls made of silicon nitride (Si3N4) versus steel ones. This study thus focuses on tapered rollers. Thanks to experimental and numerical means, the thermal behavior of tapered roller bearings is investigated for both steel and silicon nitride rollers. Various operating conditions (rotational speed, oil flow rate and oil temperature) are tested to allow the comparison of the behavior of both bearing set-ups (full-steel and hybrid). A thermal model is developed according to the thermal network method and is validated thanks to experimental results. It is then used to analyze behaviors observed during experiments, related to thermal exchanges and power losses. The effect of changing the mechanical and thermal properties of the roller material is investigated.
This paper introduces an experimental approach to study the distribution of power losses in an oil jet-lubricated planetary gear set, with the aim of increasing the efficiency of these gearboxes. A thermal model is developed to estimate power losses associated with temperature distribution. This model is applied to analyze experimental data collected from a dedicated test setup. Different configurations are studied to progressively validate the thermal network. In this paper, only a configuration composed of a rotating ring gear and a fixed planet carrier is studied. This configuration enables the validation of a thermal network developed from a basic configuration where power loss sources are not numerous. The study reveals that, for this configuration, load-independent power losses are primarily attributed to hydrodynamic losses in the bearings, while the gear windage effects are of second order. The power losses are then compared to those generated by the same planetary gear set but using a rotating planet carrier. The comparison shows that the configuration composed of the rotating ring gear and fixed planet carrier produces less power loss than the other configuration.
28 August 2024 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
In a gear transmission, power losses come from a variety of sources, classified as load-dependent and no-load-dependent losses. No-load-dependent losses are the ones that remain constant regardless of the applied load, such as losses due to drag in rolling element bearings, seals, churning and/or windage for gears. Load-dependent losses include friction losses due to sliding and rolling between gear teeth. These losses are particularly important in some gear transmissions because of their direct impact on overall efficiency and thermal behaviour. Consequently, knowledge of the friction coefficient associated to this loss is of major interest for optimising gears (geometry, surface finish, lubrication, etc.). In this article, a new method is proposed for predicting the mechanical efficiency losses associated with the mean coefficient of friction for pairs of cylindrical gears. It is based on a model developed previously to estimate the instantaneous tooth friction along the plane of action in gears. This model takes into account the lubricant shear and the friction on contacting asperities. The proposed mean friction coefficient is deduced from the instantaneous friction coefficient using specific calculations, particularly at the pitch point. To verify the method, the estimated results are compared with those in the literature calculated for gears and operating conditions common on FZG test rigs.