Parallel connections of lithium-ion cells in battery systems lead to current distributions between the cells, which impacts fast charging capabilities. This study examines the influence of interconnection resistance, format, electrode design, cell-to-cell variations, and temperature differences on system inhomogeneity and identifies anode potential safety margins that ensure safe charging without lithium plating. To this end, a physico-chemical parameterization of the Molicel INR21700-P45B is presented. An optimized fast-charging profile enables charging from 10%–80% cell capacity in under 10 minutes. The experimental application of the fast-charging profile yielded a result of over 300 equivalent full cycles before reaching 90% state of health. Furthermore, the cell model is scaled to different parallel-connected systems in an extensive simulation study. The interconnection resistance, and analogously the internal-to-interconnection resistance ratio, was found to be the primary factor influencing inhomogeneity in high parallel configurations, whereas cell-to-cell resistance variations are the most significant determinant in low parallel configurations. Variations in cooling were found to be more impactful than initial temperature disparities.
Recent studies presented the advantages of incorporating solid-polymer-electrolyte (SPE) interlayers in all-solid-state batteries (ASSB). Still, drawbacks regarding the cell performance are expected due to additional polymer-related overpotentials. The pseudo-two-dimensional (p2D) physicochemical model is extended to account for Li-ion transport in the SPE interlayer and in the ceramic LLZO solid electrolyte (SE), as well as for the charge transfer at the SPE∣LLZO interface using Butler-Volmer-like kinetics. The overpotential analysis for a reference parameterization disclosed a dominant overpotential contribution from the SPE∣LLZO charge transfer and a facilitation with increasing discharge C-rate. Variance-based global sensitivity analyses demonstrate that as the exchange current density between SPE and LLZO increases, polarization losses exhibit an exponential-like reduction. Additionally, the radius of the active material (AM) particles within the composite cathode exerts a significant and dominant influence on cell performance. With an optimization of the SPE∣LLZO exchange current density, the accessible capacity could be increased compared to the reference parameterization from 41% to 61% for a 2C discharge.
28 June 2024 in Journal of the Electrochemical Society
The occurrence of lithium plating during fast charging poses a safety risk and can reduce the battery lifespan. To prevent plating during the application of model-based charging protocols, a safety margin is added to the lithium plating voltage criterion to compensate for unaccounted in-plane heterogeneities. This article investigates the value of this safety buffer when using real-time capable 1D-DFNs coupled with a 0D thermal model. Through comparison with a multi-scale model, the 1D-DFN error to the local minimum in the anode potential can be characterized. An adjusted cooling coefficient enables 0D temperature modeling with an average error of less than 1 ◦C, despite the inability to consider temperature gradients. For a high-energy NMC811/SiC parameterization of a 4680 format cell with tabless current collectors, the 1D-DFN error in the anode potential deviates by a maximum of 10 mV during charging up to 3C at 50 W m−2 K−1 convective mantle cooling. The anode potential error is influenced by the charging rate, cooling strategy, cell format, and current collector design.
Due to challenges in manufacturing composite cathodes with oxide solid electrolytes, new cell concepts are emerging in which the infiltration of solid-polymer electrolyte (SPE) into 3D cathode pore structures improves capacity retention and cycling stability. However, the performance limitation and the resulting practical relevance of such a hybrid concept have not yet been analyzed and discussed. This study investigates the impact of laser-ablated geometric structures on the performance of hybrid solid-state batteries (SSBs). A Doyle–Fuller–Newman modeling approach is developed and parameterized for structured hybrid SSBs that incorporate a PEO/LiTFSI SPE and an LLZO ceramic separator, as well as NMC-811 and Li-metal for the positive- and negative-electrode active materials. Comparison between structured and planar cell designs reveals significant rate capability improvements in structured designs due to reduced diffusion and interfacial charge transfer polarization. A sensitivity analysis of geometric structure parameters shows further potential for performance improvement in terms of specific capacity and energy density. However, current constriction effects in the LLZO separator can deteriorate the rate capability. A more general perspective is then taken by analyzing the impact of changing SPE parameters. An energy density of 128 Wh kg−1 at 1C, and 220 Wh kg−1 at 1C with improved SPE parameters is achieved in the best case, approaching the target of 250 Wh kg−1, which is currently achieved for conventional Li-ion batteries.