The emergence of fast-switching wide-bandgap (GaN, SiC) power electronics devices has enabled motor drive systems to achieve high efficiency, power density, control bandwidth and high-level of integration. However, the fast-switching speed and high switching frequency result in an increased level of motor overvoltage at both motor terminals and stator neutral. This overvoltage increases the stress across the motor winding insulation and bearings. This paper investigates three types of motor overvoltages, i.e., differential mode (DM) (phase-to-phase) motor terminal overvoltage, common mode (CM) (phase-to-ground) motor terminal overvoltage and CM stator neutral overvoltage (motor neutral to ground). Both the high switching speed (high dv/dt) effect and the high switching frequency effect on the motor overvoltage are investigated in this paper, where the high switching frequency effect has not been fully addressed in existing literature. Significant overvoltage is observed when the switching frequency or its multiples coincide with the cable or motor anti-resonant frequency. The anti-resonant behavior in the cable and motor impedance has been used to identify the overvoltage oscillation frequency and to explain the overvoltage observations for the three types of motor overvoltages. The analysis has been tested using a 7.5kW motor setup with and without a four-core cable, driven by a SiC or a GaN three-phase inverter with a switching frequency up to 250kHz and switching speed up to 40kV/μ s. In addition, the motor bearing current, which is a main cause of bearing degradation, has also been tested and the increase of bearing current is observed due to the high frequency effect.
Compared with silicon (Si) IGBTs, silicon carbide (SiC) MOSFETs have much faster switching speeds and high switching frequency operation capability, enabling compact and high-efficiency motor drive systems. However, the increased switching speed and frequency also cause increased-level of common-mode (CM) voltage with higher slew rates ( dv / dt ). The CM voltage leads to machine leakage currents as well as bearing currents such as electric discharge machining (EDM) type current and capacitive-type ( dv / dt ) current. These bearing currents can cause degradation or failure of motor bearings. In order to investigate the impact of SiC motor drives on the motor bearing currents, in this paper, the mechanism and modelling of bearing currents are analyzed first. Then, a direct measurement method is used to assess the bearing currents in the induction motor driven by the SiC converter. In the experiment, the number of EDM current events is counted and the amplitude of the capacitive-type of current is also examined under various switching speeds and frequencies of SiC devices. Furthermore, the bearing currents are also extensively tested under various bearing temperatures, motor speeds and dc-link voltages. The correlations between the bearing currents and various factors have been revealed in this paper.
8 June 2021 in IEEE Transactions on Industry Applications
There is a continuous demand for high-power, high-efficiency, and high-density converters in various existing and emerging applications such as large motor drives, electric vehicles, more electric aircraft, and utility applications. Compared with conventional silicon (Si) insulated gate bipolar transistors (IGBTs), silicon carbide (SiC) MOSFETs can have lower switching loss and higher frequency operation capabilities, which enables higher efficiency and higher power density at the converter level. Meanwhile, to achieve a high power rating such as 500 kW, how to extend the current capabilities of existing SiC power modules, the choice of parallel schemes, the selection of passive components, cooling and mechanical structure design pose clear challenges in maximizing the system power density and efficiency. This article presents a comprehensive design of the world-first air-cooled 500 kW SiC dc/ac three-phase converter, which achieves a record-high power density of 1.246 MW/m 3 (1.246 kW/L) and an efficiency over 98.5%. The converter has been tested in the experiment to the full power rating, which provides benchmark results for high power SiC converters and their applications.
There is a continuous demand for high-power, high-efficiency and high-density converters in various existing and emerging applications such as large motor drives, electric vehicles, more electric aircraft and utility applications. Compared with conventional silicon (Si) IGBTs, silicon carbide (SiC) MOSFETs can have lower switching loss and higher frequency operation capabilities, which enables higher efficiency and higher power density at the converter level. Meanwhile, to achieve a high power rating such as 500kW, how to extend the current capabilities of existing SiC power modules, the choice of parallel schemes, the selection of passive components, cooling and mechanical structure design pose clear challenges in maximizing the system power density and efficiency. This paper presents a comprehensive design of an air-cooled 500kW SiC DC/AC three-phase converter, which achieves a high power density of 1.246MW/m 3 (1.246kW/L) and an efficiency over 98.5%. The converter has been tested in experiment to the full power rating, which provides benchmark results for high power SiC converters and their applications.
Wide-bandgap power devices, particularly silicon carbide (SiC) MOSFETs, have seen widespread adoption in electric vehicle (EV) motor drive systems due to their superior switching characteristics, including high switching speeds and high switching frequencies. However, these advantages exacerbate motor terminal overvoltage, with peaks reaching twice the inverter output voltage, causing insulation breakdown in windings and bearing electro-corrosion, which shorten motor lifespan. Traditional overvoltage prediction methods, such as distributed parameter models or detailed ladder network approaches, require extensive system parameters and involve high computational loads, while simplified models lack generality. To address these issues, this paper proposes a simplified prediction method based on a lumped ladder network model combined with frequency scanning. The approach uses impedance analysis to identify anti-resonance frequencies, enabling direct estimation of overvoltage amplitudes without prior knowledge of cable or motor specifics. Experimental validation on a SiC-based drive system demonstrates prediction errors below 10% and a reduction in computational time compared to conventional methods.
Silicon carbide (SiC) three-phase converters are widely adopted in parallel power distribution systems for their high efficiency, yet their performance is challenged by high switching frequency and communication constraints. For the parallel inverter system, problems such as uneven power distribution and circulating current may occur. Therefore, the droop control method was proposed. The droop control method is limited in precise power sharing and circulating current mitigation. To address these issues in the communication-free parallel inverter system, a hybrid droop-enhanced virtual impedance method is proposed. The methodology integrates droop characteristics with frequency-selective virtual impedance compensation, enabling concurrent optimization of power sharing and circulating current suppression. Through simulation, the droop control method and the improved droop control method were compared and analyzed. Finally, the effectiveness of the improved droop control method was verified through experiments.