Photonic integrated circuits based on ultralow loss silicon nitride waveguides have shown significant promise for realizing high-performance optical systems in a compact and scalable form factor. For the first time, we have developed a Fabry-Perot Bragg grating nanoresonator based on silicon nitride on silicon dioxide platform with an ultra-high intrinsic quality factor of 19.3 million. By combining the introduction of tapered grating between cavity and periodic Bragg grating, increasing the width of cavity to multi-mode region and optimized annealing strategy for Si3N4 film, the propagation loss is reduced to around 0.014 dB/cm. Fabry-Perot Bragg grating nanoresonator can be easily implemented in a simple straight waveguide occupying a minimal amount of space. Therefore, it is a key component to build a high performance photonic integrated circuit for many applications.
In this paper, we present the design, optimization, and implementation of a sub-wavelength grating (SWG) multi-mode interference coupler (MMI) on the silicon nitride photonic integrated circuit (PIC) platform with a significantly enhanced bandwidth compared to the conventional MMI. We extend the SWG MMI theory, previously presented for the silicon-on-insulator platform, to the Si3N4/SiO2 platform. Our approach involves an initial parameter optimization for a non-paired design, followed by a shift to a paired design that offers a smaller footprint and a broader bandwidth. The optimized SWG MMI exhibits a 1 dB bandwidth of 300 nm for both the insertion loss and power imbalance, making it a significant addition to silicon nitride photonics.
We report the design and characterization of a high performance integrated arbitrary filter from 1450 to 1640 nm. The filter's target spectrum is chosen to suppress the night-sky OH emission lines, which is critical for ground-based astronomical telescopes. This type of filter is featured by its large spectral range, high rejection ratio, and narrow notch width. Traditionally it is only successfully accomplished with fiber Bragg gratings. The technique we demonstrate here is proven to be very efficient for on-chip platforms, which can bring many benefits for device footprint, performance, and cost. For the design part, two inverse scattering algorithms are compared, the frequency domain discrete layer-peeling (f-DLP) and the time domain discrete layer-peeling (t-DLP). f-DLP is found to be superior for the grating reconstruction in terms of accuracy and robustness. A method is proposed to resolve the non-uniformity issue caused by the non-zero layer size in the DLP algorithm. The designed 55-notch filter is 50-mm-long and implemented on a compact Si 3 N 4 /SiO 2 spiral waveguide with a total length of 63 mm. Experimentally, we demonstrate that the device has a insertion loss as low as 2.5 dB, and that the waveguide propagation loss is as low as 0.10 dB/cm. We are also able to achieve uniform notch depths and 3-dB widths of about 28 dB and 0.22 nm, respectively.
In this work, we present a CuInSe$_{2}$ (CIS) thin-film solar cell with 14.7% efficiency and 40.2-mA/cm2 short-circuit current. The samples were fabricated by the selenization of stacked elemental layers under selenium vapor in atmospheric ambient within a simple graphite box. Some samples were treated with a postdeposition treatment (PDT) with potassium fluoride (KF), whereas some were not, thus allowing for useful comparison. The use of the KF PDT led to two interesting improvements on our samples: formation of a hole-blocking layer between CdS/CIS interface, which reduces the tunneling recombination and significantly increases the open-circuit voltage. In addition, the KF PDT clearly reduces the symmetry of the nonohmic shunt leakage at low forward bias and reverse bias, which can be explained by a space-charge-limited current model, indicative of metal–semiconductor–metal (MSM) shunts. Discussion is presented to understand possible defects introduced during our processing steps and the physical origin of the shunt paths and why they might be of the MSM type. New directions to improve the performance of CIS solar cells are presented for future work using this very simple fabrication technique.
To provide a solution to the issue of the non-flat focal surface in traditional Rowland AWGs, we have designed and implemented a Si3N4 three-stigmatic-point arrayed waveguide grating (TSP AWG) with three inputs, and a spectral resolving power over 17,000 has been achieved experimentally. The flat focal surface of this AWG can accommodate a butt-coupled detector array positioned at the output facet without any reduction of the resolving power of the edge channels. Therefore, it is particularly advantageous to some astronomical applications which require an AWG as a light-dispersing component to obtain a complete 2D spectrum. As a proof-of-concept for next generation devices, the multi-input aspect of the design accommodates multiple single-mode fibers coming into the AWG. In addition, because the device is implemented on a high-index-contrast platform (Si3N4/SiO2), a compact size of ∼9.3 × 9.3 mm2 is achieved.
In this paper, we present an ultra-broadband double-tip edge coupler with high coupling efficiencies for both TE and TM polarizations on a silicon nitride platform. The coupler is designed for the high NA fiber which provides a smaller mode size. In simulations, both TE and TM coupling efficiencies remain above 90% within the wavelength range 1000–2000 nm. In comparison, the TE and TM coupling efficiencies of the conventional single-tip coupler design can drop below 73% over this range. An ultra-high coupling efficiency above 95% is predicted over a bandwidth of 760 nm for the TE mode with the double-tip design, compared to 450 nm for the single-tip design. Experimentally, the highest measured coupling efficiencies for the double-tip and single-tip couplers are 97.1% and 95.7%, respectively. For the double-tip design, the coupling efficiency remains above 90% within the measurement range (1450–1640 nm), as the polarization state changes with the wavelength. These measurements confirm the polarization insensitivity of the double-tip design. In addition, we measure the performance of the double-tip design with a laser source operating at shorter wavelengths. The measured 94% coupling efficiency at 1280 nm indicates the broad bandwidth of the coupler. This work is anticipated to provide a promising foundation for the development of compact efficient photonic devices.