This letter presents a ${K}$ -band 0.1- $\mu \text{m}$ GaN on Si 10-W high-power amplifier (HPA) for the downlink of the satellite communication system. The proposed HPA uses the driver-stage transistor to generate a half-sinusoidal waveform that is delivered to the power-stage transistor. The half-sinusoidal waveform combines the input nonlinearity of the power-stage transistor to simultaneously improve the efficiency and expand the design space of the input harmonic impedance. A simple and compact interstage matching network (ISMN) design is used to match the harmonic impedance of both driver and power-stage transistors to create the corresponding waveforms. The proposed HPA has a small size of 3.5 mm $\times3.2$ mm and operates in the frequency range of 17–20.5 GHz achieving a 22-dB gain, an average output power ( ${P}_{\mathbf {out}}$ ) of 42 dBm, and 41% power-added efficiency (PAE) in the pulsed measurement. Moreover, the proposed HPA maintains a PAE of more than 33% and output power of 40.4 dBm in continuous wave (CW) measurement.
2 January 2023 in IEEE Microwave and Wireless Technology Letters
This letter describes a design of a 3.3–3.6-GHz GaAs heterojunction bipolar transistor (HBT) power amplifier (PA) with high linearity and temperature insensitivity for the fifth-generation (5G) of new radios (NRs). By involving a multi-feedback branches bias circuit, the voltage at the feedback node of the bias circuit can achieve dynamic self-tuning to stabilize the base voltage as the amplifier’s input power grows and stabilize the bias current as the temperature increases as well. A three-stage common source structure PA in the form of a monolithic microwave integrated circuit (MMIC) is designed using a multi-feedback branch bias circuit with a size of 1.5 $\times$ 1.2 mm. Measured with continuous wave (CW) signals, the output 1-dB compression point at 3.3–3.6 GHz is 34 dBm. The linearity of the PA is also evaluated using a 5G-NR 100-MHz 64-quadratic-amplitude modulated (QAM)-orthogonal frequency division multiplexing (OFDM) signal with a 7-dB peak-to-average-power ratio (PAPR). The proposed PA achieves an adjacent channel power ratio (ACPR) less than $-$ 49.5 dBc at an average power of 28 dBm with a power-added efficiency (PAE) of 20% without the use of digital pre-distortion (DPD). In the temperature range of $-$ 40 $^{\circ}$ C to 120 $^{\circ}$ C, the variance of bias current, small signal gain, PAE, output power at 1-dB compression point (OP1dB), and ACPR is relatively minor. This design is ideally suited for 5G communication systems due to its high linearity and temperature insensitivity.
30 September 2024 in IEEE Internet of Things Journal
This article introduces a novel power amplifier integrated active antenna (PAIAA) with increased efficiency that integrates a Class-$F {^{-}1 }$ Gallium Nitride (GaN) power amplifier (PA) and a stub-loaded wide slot antenna (SLSA) for wireless power transmission (WPT) applications. Unlike conventional PA integrated active antennas in which antennas and PAs are separately matched to 50 ohms, the input impedance of the SLSA is meticulously engineered to match the fundamental impedance and modulate harmonic impedances of the GaN transistor by optimizing the dimensions of the SLSA's stubs. This approach eliminates the output matching network (OMN), the PA's harmonic modulation network (HMN), and the antenna's input matching network (IMN), which typically incur unavoidable insertion loss but are essential for conventional Class-$F {^{-}1 }$ PAs and antennas. Consequently, it enhances the power-added efficiency (PAE) within the 3.3–3.8-GHz range and reduces the overall size of the PA integrated active antenna. Thanks to the extended design freedom offered by SLSA, precise impedance values can be achieved across a broader frequency range, resulting in increased efficiency across a larger spectrum. In addition, an innovative insertion loss measurement method for impedance matching network with a non-50-$\Omega $ port is introduced to accurately measure the Class-$F {^{-}1 }$ PA's PAE incorporated in the proposed PAIAA. The measured PAIAA demonstrates a peak PAE of 70.1%, surpassing the performances of reported integrated active antennas. The measured effective isotropic radiated power (EIRP) of the proposed PAIAA is 44.52 dBm. A conventional PA-antenna design, where an antenna and a Class-$F {^{-}1 }$ PA are separately matched to $50~\Omega $ and simply cascaded, is also designed and measured as a contrast, whose measured peak PAE and EIRP of the conventional design are only 61.5% and 43.9 dBm, respectively. The proposed PAIAA, with its increased efficiency, can be practically utilized for WPT applications in the Internet of Things (IoT), where efficiency performance is critical.
25 September 2024 in IEEE Transactions on Communications
In recent years, fully-connected hybrid beamforming (FC-HBF) architecture has aroused widespread interest for millimeter wave (mmWave) massive multi-input multi-output (MIMO) communication systems. However, the FC-HBF structure suffers from significant linearity deterioration, limiting its applications in actual mmWave transmitters. To resolve this issue, an effective digital predistortion (DPD) method utilizing analytical multi-input behavioral models is proposed in this paper for linearizing the FC-HBF system. Based on the nonlinearity analysis and behavioral modeling of the array response, three analytical multi-input models are derived by embedding the priori beamforming information in the predistorter. The complexity of the proposed analytical models is significantly reduced compared to the state-of-the-art. Numerical simulations and experimental measurement are carried out on a 4×64 mmWave FC-HBF array and 2×16 quasi-test platform respectively to validate the performance of the proposed DPDs against the state-of-the-art DPDs, which show significant linearization abilities to compensate for the nonlinear distortions of beam signals. The proof-of-the-concept validations in this paper indicate that the proposed scheme is fully capable of linearizing an mmWave FC-HBF array.
4 November 2022 in IEEE Transactions on Electron Devices
In this work, a new small-signal model (SSM), which is called the distributes intrinsic subdevice model (DISDM), is established for AlGaN/gallium nitride (GaN) Fin-like high-electron mobility transistors (HEMTs) according to the device structure feature. Perfect agreements between the measured and simulated scattering parameters (S-parameters) illustrated the validity of the DISDM and the accuracy of parameters extracted from the new model. Then, the characteristics of Fin-like HEMTs are analyzed using the DISDM theoretically. Different from the traditional model, the DISDM can accurately show the characteristics of the Fin-like HEMTs, especially the “double-peak” of the intrinsic transconductance. Compared with the planar HEMTs, the Fin-like HEMTs exhibit a higher linearity in direct current and small-signal parameters. For Fin-like HEMTs with different recess depths and duty ratios, the variation of the small-signal parameters and the linearity of devices were characterized to evaluate the performance of devices and optimize the process in the end.
15 August 2025 in IEEE Microwave and Wireless Technology Letters
This article first proposes a series-shunt compact (SSC) radio frequency (RF) switch design based on gallium nitride (GaN) high-electron-mobility transistors (HEMTs) which can significantly improve the device’s isolation (ISO) and mitigate the degradation of insertion loss (IL). The design follows a distributed architecture, introducing a shunt structure on conventional HEMTs and tightly coupling the capacitances of the series and shunt parts’ active regions. This leads to an increase in $C_{\mathbf {on}}$ during the on-state, while the depletion of the negatively biased shunt gate enhances signal shielding, avoiding the effect of increased frequency on IL degradation. Moreover, the device exhibits excellent ISO performance in the off-state. Overall, these design characteristics enable the 500 nm gate-length SSC GaN HEMT to achieve an ISO larger than 14 dB, an IL flatness of 0.38 dB across the 2–20 GHz range, and a $R_{\mathbf {on}} C_{\mathbf {off}}$ coefficient of 478 fs. Currently, the SSC HEMT boasts state-of-the-art ISO metrics in single-cell devices, outperforming even some typical circuit topologies. Additionally, the SSC HEMT achieves a maximum output power ($P_{\mathbf {max}}$ ) >37 dBm and an output third-order intercept point (OIP3) = 66 dBm at 3.6 GHz. These results demonstrate the great potential of the SSC HEMT in improving ISO and mitigating IL degradation across a broad frequency band, providing new possibilities for device selection in broadband RF circuits.