In this work, a Schottky barrier diode (SBD) is fabricated and demonstrated based on the edge-defined film-fed grown (EFG) Ga2O3 crystal substrate. At the current stage, for high resistance un-doped Ga2O3 films and/or bulk substrates, the carrier concentration (and other electrical parameters) is difficult to be obtained by using the conventional Hall measurement. Therefore, we extracted the electrical parameters such as on-state resistance (Ron), Schottky barrier height (), the ideal factor (n), series resistance (Rs) and the carrier concentration (Nd) by analyzing the current density–voltage (J–V) and capacitance–voltage (C–V) curves of the Ga2O3-based SBD, systematically. The detailed measurements and theoretical analysis are displayed in this paper.
The wearable electroencephalogram (EEG) dry electrode acquisition system has shown great application prospects in mental state monitoring, the brain–computer interface (BCI), and other fields due to advantages such as being small in volume, light weight, and a ready-to-use facility. This study demonstrates a novel EEG cap with concise structure, easy adjustment size, as well as independently adjustable electrodes. The cap can be rapidly worn and adjusted in both horizontal and vertical dimensions. The dry electrodes on it can be adjusted independently to fit the scalp as quickly as possible. The accuracy of the BCI test employing this device is higher than when employing a headband. The proposed EEG cap makes adjustment easier and the contact impedance of the dry electrodes more uniform.
A way to increase the photocurrent of top-cell is crucial for current-matched and highly-efficient GaInP/GaInAs/Ge triple-junction solar cells. Herein, we demonstrate that ellipsoidal silver nanoparticles (Ag NPs) with better extinction performance and lower fabrication temperature can enhance the light harvest of GaInP/GaInAs/Ge solar cells compared with that of spherical Ag NPs. In this method, appropriate thermal treatment parameters for Ag NPs without inducing the dopant diffusion of the tunnel-junction plays a decisive role. Our experimental and theoretical results confirm the ellipsoidal Ag NPs annealed at 350 °C show a better extinction performance than the spherical Ag NPs annealed at 400 °C. The photovoltaic conversion efficiency of the device with ellipsoidal Ag NPs reaches 31.02%, with a nearly 5% relative improvement in comparison with the device without Ag NPs (29.54%). This function of plasmonic NPs has the potential to solve the conflict of sufficient light absorption and efficient carrier collection in GaInP top-cell devices.
Biosensors are devices that integrate a variety of technologies, containing biology, electronics, chemistry, physics, medicine, informatics, and correlated technology. Biosensors act as transducer with a biorecognition element and transform a biochemical reaction on the transducer surface directly into a measurable signal. The biosensors have the advantages of rapid analysis, low cost, and high precision, which are widely used in many fields, such as medical care, disease diagnosis, food detection, environmental monitoring, and fermentation industry. The enzyme biosensors show excellent application value owing to the development of fixed technology and the characteristics of specific identification, which can be combined with point-of-care testing (POCT) technology. POCT technology is attracting more and more attention as a very effective method of clinic detection. We outline the recent advances of biosensors in this chapter, focusing on the principle and classification of enzyme biosensor, immobilization method of biorecognition layers, and fabrication of amperometric biosensors, as well as the applications of POCT. A summary of glucose biosensor development and integrated setups is included. The latest applications of enzyme biosensors in diagnostic applications focusing on POCT of biomarkers in real samples were described.
Two-section distributed feedback lasers containing an active section and a modulated reflection section have been demonstrated for direct modulation with negative chirp. The reflection section has the same waveguide core and grating pitch as the active section. The active section of the laser has fixed current injection and the modulation voltage is loaded onto the reflection section when the laser normally works. This modulation method can obtain negative chirp because the carrier density variation in the active section during modulation is contrary to traditional current modulation. The threshold current and side-mode suppression ratio of the fabricated laser are about 10-mA and 60-dB at 20 °C, respectively. A 20-GHz modulation bandwidth at 0.9-V reverse bias of the modulated reflection section has been achieved. The negative chirp generated by the modulation is about 45 GHz. 10 Gb/s transmission over 10-km single-mode fiber with error-free-operation over a wide temperature range has been demonstrated as well. The sensitivity of the 10-km transmission was better than BTB configuration at all temperatures due to the negative chirp characteristic.
A miniature Fourier transform spectrometer is proposed using a thin-film lithium niobate electro-optical modulator instead of the conventional modulator made by titanium diffusion in lithium niobate. The modulator was fabricated by a contact lithography process, and its voltage-length and optical waveguide loss were 2.26 V·cm and 1.01 dB/cm, respectively. Based on the wavelength dispersion of the half-wave voltage of the fabricated modulator, the emission spectrum of the input signal was retrieved by Fourier transform processing of the interferogram, and the analysis of the experimental data of monochromatic light shows that the proposed miniaturized FTS can effectively identify the input signal wavelength.