A current challenge in realising clean road transport is non-exhaust emissions. Important advances regarding measurement systems, including well-defined characterisation techniques, as well as regulation, will be made in the next few years. In this work, we present the detailed results of particle emission analyses, consisting of aerosol (size distribution, particle number (PN), and mass (PM)) and electron microscopy (EM) measurements, under different load conditions on a test bed for a wheel suspension and brakes. Standard tyres and brakes from serial production were tested with a high-load driving cycle, while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS, and a GRIMM OPS. Furthermore, samples were analysed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with an SMPS, with peaks at 20 and around 400 . The results of an EM analysis of single particles from the electrostatic sampler match the PSD results. The EM analysis also showed ultrafine particles, mainly containing O, Fe, Si, Ba, Mg, and S, and also fractal particles with high-C fractions. Our results suggest, in agreement with the previously published literature, that particulate emissions are related to the brake disc temperature and occur in significant amounts above a threshold temperature.
The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.
17 June 2020 in Journal of Computational and Nonlinear Dynamics
Model reduction via projection is a common method to accelerate time integration of finite element (FE) structures by reducing the number of degrees-of-freedom (DOFs). However, nonlinear state-dependent surface loads are usually computed based on the nonreduced DOFs of the FE model. When a considerably high number of DOFs are involved in the nonlinear surface loads, their computation becomes a bottleneck. This paper presents a general approach for reduced time integration and reduced force computation for FE models. The required force trial vectors can be computed easily and systematically out of deformation trial vectors, commonly called “modes.” Those force trial vectors, which we call “stress modes,” can be determined a priori so that a nonlinear computation of the full system is not necessary. The new idea in this contribution is that stress recovery is used to decrease the number of equations for the force computation. A general framework for semihyper-reduction (SHR) is developed and its practical implementation is discussed. The term SHR is introduced because it is an intermediate approach between the straight-forward method of using the FE DOFs and pure hyper-reduction (HR) where the FE DOFs are omitted for computing state-depended surface loads. In order to demonstrate the proposed SHR approach practically, a numerical example of a planar crank drive is given, where a hydrodynamic lubrication film separates piston and cylinder. Thereby, very good result quality has been observed in comparison to a finite difference reference solution.
This study introduces a methodology for characterizing and modeling the viscosity and specific volume–pressure–temperature (pvT) behavior of sheet molding compound (SMC) materials, based on the use of specialized testing equipment. Conventional rheometers are inadequate for such materials due to the presence of long fibers, necessitating the use of specialized equipment like squeeze flow rheometers and pvT dilatometers. Our findings demonstrate that traditional oscillatoric rheometer measurements underestimate the viscosity of CF-SMCs, highlighting the need for advanced, albeit non-standardized, testing methods. Additionally, we found that standard Tait models failed to capture the temperature-dependent porosity of CF-SMCs at low pressures, whereas models based on thermodynamic state variables (TSVs) provided accurate predictions across a broader range of conditions. The study also addressed the complexities introduced by fiber–flow coupling and the fiber orientation in measuring the viscosity, revealing limitations in conventional modeling approaches. The numerical analysis showed that a power law-based anisotropic viscosity model (PL-IISO) combined with a TSV model offered the best predictive performance in finite volume flow simulations, especially for thick-walled regions. However, the current modeling approaches have limited predictive capabilities for the fiber orientation in thin-walled regions. This research underscores the challenges in accurately modeling CF-SMC materials in terms of the fiber orientation, whereas the compression forces needed from the pressing machine could be predicted accurately within an average error of 6.5% in the squeeze flow experiments.