This paper presents the results of voluminous experimental investigations conducted to analyze the influence of the welding procedure on the performance of regenerated gears. Cylindrical spur gears were tested, both newly manufactured and regenerated, in two fundamentally different ways: by hard facing (surfacing) with the “hard” filler metal (DUR 600-IG) and with the “soft” filler metal (EVB2CrMo) with subsequent cementation and quenching. The regeneration procedures were defined and executed, while, subsequently, the microstructure and microhardness of the hard-faced layers were established and measured, followed by checking the durability of the hard-faced teeth flanks. Finally, techno-economic analysis was performed to establish the rationality of the conducted regenerations, i.e., the costs of regenerated and newly manufactured teeth were compared. Based on the results of the conducted investigations, it was possible to establish the influence of the welding type on the performance characteristics (primarily the service life) of the regenerated gears. For individual reparatory hard facing, the procedure with the “hard” filler metal exhibited better characteristics, while for batch reparation of numerous damaged gears, the reparation with the “soft” filler metal, followed by cementation and heat treatment, might be more convenient.
The principles of the friction welding (FW) process of the two different non-ferrous metals, aluminum and copper, are presented in this paper. Considering that the bimetallic Al-Cu joints find applications in electrical engineering, as well as in other industrial fields, the basic characteristics and compatibility of these metals are discussed, along with the influence of various parameters on the properties of their friction welded joints. The experimental study involved rotation friction welding (RFW), which was used to weld aluminum and copper samples. The samples were monitored for shortening due to the applied deformation, as well as the size of the formed mushroom. Then, the central part of the welded joint was cut from the welded samples to determine the hardness and microstructure of the joint. At the end of the research, the possibility of applying software for the design of a numerical model for analysis of the possibility of joining aluminum and copper, with the same input parameters as those used in the experiment, was considered. The numerical simulation exhibited a high agreement with the experimental results.
An analysis of the friction time influence on creation and structure of the mixing zone during the friction welding process of the two dissimilar steels is presented in this paper. The changes were monitored on the two welded samples, made of ...
Additive manufacturing of polymer tools represents a promising alternative to conventional steel tooling for low-force and low-volume sheet metal air bending. However, accurate prediction of sheet springback and the resulting deviation of the bending angle after elastic unloading remains a major challenge. This study presents an integrated experimental–numerical framework for the analysis of air bending with additively manufactured polymer tools, with emphasis on material characterization, springback prediction, and tool angle compensation. The methodology combines uniaxial tensile testing, controlled air-bending experiments, finite element modelling with rigid and deformable tools, and optical 3D scanning for angle measurement. Low-carbon steel DC04 sheets were modeled using an elastoplastic constitutive law, while additively manufactured ABS tools were described by experimentally calibrated material models. Numerical simulations were performed over a range of forming forces to evaluate springback behavior and elastic tool deformation. The results show very good agreement between experiments and simulations. Deviations in bending angle were below 1.5% for metallic tools and below 0.5% for springback compensation, with the smallest discrepancy obtained using a two-dimensional model with deformable tools. Experimental validation with ABS tools confirmed bending accuracy within ±1°. The proposed framework provides a reliable basis for springback prediction and rational design of additively manufactured polymer tools for air-bending applications.
Individual activities in new media in much of the literature are considered separate and unrelated to the offline world. This research shows that activities in new media actually involve individual activities in everyday life. The popularity of coffee shop culture cannot become an urban culture without the role of new media. The presence of new media allows individuals or influencers to share photos and videos while in coffee shops. A coffee shop is also a good, aesthetic, contemporary object for all the services, food and drinks provided to consumers. This condition is what coffee shop consumers take advantage of to share their activities through new media. The aim of this research is to find out if activities in coffee shops are widely seen in new media by fellow users, friends and family, so that they attract a lot of interest from urban communities. This research uses qualitative methods and data collection techniques through in-depth interviews and field observations (coffee shops). The result of this research is that in the end each individual tries to produce interesting video and photo content in order to get comments, likes/dislikes in new media. Based on the results and discussion The presence of new media makes it possible for each user to be able to interact flexibly and produce content according to their abilities and wishes. The novelty of this research is that positive responses are a form of pride and happiness for those who post them on new media
The principles of the friction welding (FW) process of the two different non-ferrous metals, aluminum and copper, are presented in this paper. Considering that the bimetallic Al-Cu joints find applications in electrical engineering, as well as in other industrial fields, the basic characteristics and compatibility of these metals are discussed, along with the influence of various parameters on the properties of their friction welded joint. The experimental study involved determining and analyzing the effects of process parameters on the occurrence, shape, and level of plastic deformation resulting from changes in the physical model during the rotational friction welding process (RFW). The specificity of the joining process is in the occurrence of various phenomena in the weld zone, which are significantly affecting the physical, structural, and mechanical properties of the base materials, thus influencing the joint quality. The friction welding process itself is complex, and the task is further complicated by the use of different base materials.