We report on, to the best of our knowledge, the first fs-laser-written waveguide laser in (Yb:CALGO). With Yb:CALGO crystals grown in our labs, we obtained a slope efficiency of 69% and up to 2.4 W of continuous wave (cw) output power in a waveguide-laser configuration. Moreover, bulk laser experiments with Yb:CALGO were performed, and slope efficiencies up to 73%, optical-to-optical efficiencies of 65%, and maximum cw output powers of 3.3 W were reached. These are the highest efficiencies in the laser configuration with Yb:CALGO.
Ultrafast laser driven, single-cycle THz pulsed sources hold immense potential for scientific and industrial applications; however, their limited average power hinders their widespread application. In particular, applications where high repetition rates in the multi-MHz region and beyond are required are more severely affected, due to the lower pulse energies available for frequency conversion. In this respect, resonant enhancement both in passive and active resonators is a well-known technique for boosting the efficiency of nonlinear frequency conversion; however, this route has remained poorly explored for the generation of broadband THz pulses due to the inadequacy of typically employed nonlinear crystals. Here, we demonstrate that using thin lithium niobate crystals inside multimode diode-pumped mode-locked thin-disk lasers is a promising platform to circumvent these difficulties. Using a 50 µm thin lithium niobate plate intracavity of a compact high-power mode-locked thin-disk laser, we generate milliwatt-level broadband THz pulses with a spectrum extending up to 3 THz at 44.8 MHz repetition rate, driven by 264 W of intracavity average power. This approach opens the door to efficient high-power single-cycle THz generation using affordable nonlinear crystals at very high repetition rates, scalable to kilowatt-level driving power with low cost and complexity.
Here, we report on the fabrication of cm-long microchannels in LiNbO3 by selective etching of femtosecond laser inscribed tracks using hydrofluoric acid. We achieved a 1 cm long microchannel after 300 h of etching a single track inscribed into the volume along the optical axis of LiNbO3. Furthermore, we investigated the dependence of the etching behavior on various writing parameters. Highly selective etching with a selectivity up to 104 was achieved and a functional relationship between the etched depth and time was found. Thus, our results set the first milestone for future fabrication of 3D-hollow microstructures in the volume of LiNbO3 combining its outstanding physical properties such as the strong nonlinearity as well as the acousto- and electrooptic properties with both microfluidic and photonic structures in a monolithic setup.
We demonstrate multi-cycle terahertz (MC-THz) generation in a 15.5 mm long periodically poled rubidium (Rb)-doped potassium titanyl phosphate (Rb:PPKTP) crystal with a poling period of 300 µm. By cryogenically cooling the crystal to 77 K, up to 0.72 µJ terahertz energy is obtained at a frequency of 0.5 THz with a 3 GHz bandwidth. A maximum internal optical-to-terahertz conversion efficiency of 0.16% is achieved, which is comparable with results achieved using periodically poled lithium niobate crystal. Neither photorefractive effects nor damage was observed with up to , showing the great potential of Rb:PPKTP for multi-millijoule-level MC-THz generation.
A neodymium (Nd) doped lithium-niobate-on-insulator (LNOI) was fabricated from a lithium niobate (LN) substrate diffusion-doped with Nd prior to the LNOI fabrication process. Diffusion doping enables the fabrication of differently doped regions on a single LNOI substrate, a key advantage for future applications in highly integrated photonics. Fluorescence spectra, emission cross-section, fluorescence lifetime, and small-signal gain of Nd:LNOI were determined for the first time to our knowledge and compared with data published for diffusion-doped ridge or channel waveguides in LN substrates. For an 11 mm-long sample, we achieve a small-signal gain for π (σ) polarization of about 14 (10) dB when pumping with a Ti:Sapphire laser, which is promising for future active components in Nd:LNOI like amplifiers and lasers.
Single-cycle, high-power, high-repetition-rate THz pulse sources are becoming the cornerstone of several scientific and industrial applications. A promising and versatile method for high-power THz generation is optical rectification in nonlinear crystals pumped by powerful near-infrared ultrafast laser systems. In this context, ytterbium-based laser sources are particularly advantageous in terms of power scalability and technology establishment. However, as the repetition rate increases toward hundreds of MHz, the conversion efficiency typically decreases, as most laser systems do not reach sufficiently high average powers to correspondingly enhance the peak power to drive the nonlinear conversion process efficiently. An alternative approach to achieving a sufficiently high average power at a high repetition rate is based on passive enhancement cavities, which boost the pulse energy of standard watt-level ytterbium lasers by orders of magnitude. We present the first demonstration of optical rectification in a passive enhancement cavity at multi-kW levels, achieved by a 240-fold power enhancement. By irradiating a 50-μm thin lithium niobate plate with 1.9-kW average power inside the enhancement cavity, we generate milliwatt-level THz pulses with 2-THz bandwidth and 93-MHz repetition rate, mostly limited by the driving pulse duration. To the best of our knowledge, this represents the highest driving average power used for optical rectification. This methodology represents a promising new step toward high-repetition-rate and high average power single-cycle THz sources using widely available multi-watt level Yb lasers.