In this study, three different surfaces of Titanium-coated PEEK were compared by their coating strength, cell adhesion, and cell growth, which were produced through electron beam PVD. For this purpose, different samples with smooth, moderate, and coarse roughness surface were prepared. Surface roughness measurement, AFM, SEM, and EDS analyses were applied to compare surface topography, observe the thickness and roughness of the coated surface, and characterised coated materials, respectively. Also, cross-cut, in vitro and in vivo tests were performed to measure adhesion strength and biological differences between samples to validate data on the optimum sample. The results showed that the adhesion strength between the coated layer and the substrate for every sample was reliable, but Cell adhesion for the sample with moderate roughness was the best among all. Therefore, moderate surface roughness was found to be optimum due to the obtained results from the interaction between implant surface and cells. GRAPHICAL ABSTRACT

Humidity sensors are essential components in modern technology, spanning applications from residential appliances to the Internet of Things (IoT). However, conventional commercial sensors are typically rigid, constrained by narrow relative humidity (%RH) operating ranges, and require complex fabrication processes. In this study, we present a highly sensitive cubic silicon carbide (3C–SiC) nanoparticle-based relative humidity sensor, fabricated via serigraphic printing on to 5 mil thick flexible polyimide (Kapton^®) substrate. Devices are tested across a broad humidity range of 10–90%RH at ambient temperature and their performance is evaluated in a controlled humidity chamber. The sensor exhibits a robust response of 45.2% R/R₀, with a sensitivity of 5.34 Ω/%RH, an adsorption time of 18 seconds, and a desorption time of 46 seconds. Additionally, the device demonstrates low hysteresis of 6.5% at 60%RH, with excellent repeatability and stability over 3.5 hours of continuous cycling. To showcase their potential for real-world applications, the printed sensors are integrated into a commercial KN95 mask for monitoring respiration parameters, such as respiration rate. This integration highlights the potential for future exploration in human health monitoring, utilizing fully printed, low-cost sensing devices.

This review article provides a comprehensive analysis of the photonic sintering conditions necessary to process non-oxide ceramics, to obtain similar material properties when compared with those of thermally annealed ones, for various applications in printed electronics. This article presents a thorough examination of the scientific literature on this topic, discussing the principles of photonic sintering applied to non-oxide ceramics, its advantages over traditional post-processing methods, and a quantitative overview of the performance of devices fabricated with the crystalline materials obtained.

The most common method of processing metal oxide and perovskite thin films in the laboratory is thermal annealing (TA), which is a constraint for the commercialization of large-scale perovskite solar cells. Here, we present a photonic curing (PC) process to produce fully photonically annealed perovskite cells—a fast process with well-controlled, short light pulses—to develop perovskite photovoltaic devices with high efficiency. We also demonstrate how to use the parameters of the photonic annealing system to control the optical, electrical, morphological, and structural properties of perovskite layers for photovoltaic device applications. The effect of PC treatment on the microstructure, granularity, and electronic properties was studied by scanning electron microscopy (SEM), photoluminescence (PL), and transient photocurrent (TPC). The degree of conversion of the perovskite precursor and its influence on the electronic structure have been identified. $\mathrm{S}\mathrm{n}{\mathrm{O}}_2$ and perovskite films were treated with a single pulse and produced PCE comparable to control samples treated by TA.

The most common method of processing metal oxide and perovskite thin films in the laboratory is thermal annealing (TA), which is a constraint for the commercialization of large-scale perovskite solar cells. Here, we present a photonic curing (PC) process to produce fully photonically annealed perovskite cells - a fast process with well-controlled, short light pulses - to develop perovskite photovoltaic devices with high efficiency. We have also demonstrated how to use the parameters of the photonic annealing system to control the optical, electrical, morphological, and structural properties of perovskite layers for photovoltaic device applications. The effect of PC treatment on microstructure, granularity, and electronic properties was studied by scanning electron microscopy (SEM), photoluminescence (PL), and transient photocurrent (TPC). The degree of conversion of the perovskite precursor and its influence on the electronic structure have been identified. SnO2 and perovskite films were treated with a single pulse and produced PCE comparable to control samples treated by TA.