Ricardo Alexandre

Mr. Ricardo Alexandre

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2011 in Journal of Nanoscience and Nanotechnology
Verified
Journal Article
Open access
RMRui Martinho
Rui Martinho
Francisco J. G. SilvaFrancisco J. G. Silva
Francisco J. G. Silva
RARicardo Alexandre
Ricardo Alexandre
ABA. P. M. Baptista
A. P. M. Baptista
In the injection moulding of polypropylene reinforced with hard glass fibres, die materials are commonly subjected to severe abrasive wear. In order to improve its wear resistance, an unbalanced magnetron sputtering PVD compositional monolayered coating has been produced. The film was composed by a nanostructured TiB2 monolayer. Microstructure characterization and thickness evaluation were conducted by scanning electron microscopy (SEM). Film topography and roughness were accessed by SEM and Atomic Force Microscopy (AFM). The phase analyse was investigated by X-ray diffraction (XRD), using Cu K radiation. Scratch tests were conducted in order to study the film adhesion to the substrate. Load–Displacement curves (nanoindentation analysis) allowed measuring the film hardness and Young's modulus. A ball-cratering tribometer was used to determine the micro-abrasion laboratorial wear resistance, under different tests conditions, using SiC particles in distilled water slurry. At the end of these tests, the worn surfaces were analyzed by SEM and Energy Dispersive X-ray Spectroscopy (EDS) in order to compare these results with some other coatings already tested in the same conditions. To test the practical wear resistance, 135000 injection cycles were done in a plastic injection industrial mould. Coated samples were put on the plastic feed canal, after a turbulent zone. In these tests, a 30%(wt) glass fibres reinforced polypropylene was used. Worn sample surfaces were analyzed by SEM after 45.000 and 90.000 cycles. Image analyses were made in order to evaluate the damage increases and to observe the wear mechanisms involved.

1 December 2012 in Journal of Nanoscience and Nanotechnology
Verified
Journal Article
Open access
Francisco J. G. SilvaFrancisco J. G. Silva
Francisco J. G. Silva
RMRui Martinho
Rui Martinho
RARicardo Alexandre
Ricardo Alexandre
ABA. P. M. Baptista
A. P. M. Baptista
In the last decades TiAlN coatings deposited by PVD techniques have been extensively investigated but, nowadays, their potential development for tribological applications is relatively low. However, new coatings are emerging based on them, trying to improve wear behavior. TiAlSiN thin coatings are now investigated, analyzing if Si introduction increases the wear resistance of PVD films. Attending to the application, several wear test configurations has been recently used by some researchers. In this work, TiAlSiN thin coatings were produced by PVD Unbalanced Magnetron Sputtering technique and they were conveniently characterized using Scanning Electron Microscopy (SEM) provided with Energy Dispersive Spectroscopy (EDS), Atomic Force Microscopy (AFM), Electron Probe Micro-Analyzer (EPMA), Micro Hardness (MH) and Scratch Test Analysis. Properties as morphology, thickness, roughness, chemical composition and structure, hardness and film adhesion to the substrate were investigated. Concerning to wear characterization, two very different ways were chosen: micro-abrasion with ball-on-flat configuration and industrial non-standardized tests based on samples inserted in a feed channel of a selected plastic injection mould working with 30% (wt.) glass fiber reinforced polypropylene. TiAlSiN coatings with a small amount of about 5% (wt.) Si showed a similar wear behavior when compared with TiAlN reported performances, denoting that Si addition does not improve the wear performance of the TiAlN coatings in these wear test conditions.

2 August 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MRMariana Relva
Mariana Relva
DSDaniela Santo
Daniela Santo
RARicardo Alexandre
Ricardo Alexandre
Pedro FaiaPedro Faia
Pedro Faia
Sandra CarvalhoSandra Carvalho
Sandra Carvalho
Susana DevesaSusana Devesa
Susana Devesa
Titanium alloys such as Ti-6Al-4V are widely used in biomedical implants due to their excellent mechanical properties and biocompatibility, but their bioinert nature limits osseointegration and antibacterial performance. This study proposes a multifunctional surface coating system integrating a thermally oxidized TiO2 interlayer with a hydroxyapatite (HAp) top layer synthesized via a green route using Hylocereus undatus extract. The HAp was deposited by electrophoretic deposition (EPD), enabling continuous coverage and strong adhesion to the pre-treated Ti-6Al-4V substrate. Structural, morphological, chemical, and electrical characterizations were performed using XRD, SEM, EDS, Raman spectroscopy, and impedance spectroscopy. Bioactivity was assessed through apatite formation in simulated body fluid (SBF), while antibacterial properties were evaluated against Staphylococcus aureus. The results demonstrated successful formation of crystalline TiO2 (rutile phase) and calcium-rich HAp with good surface coverage. The HAp-coated surfaces exhibited significantly enhanced bioactivity and strong antibacterial performance, likely due to the combined effects of surface roughness and the bioactive compounds present in the plant extract. This study highlights the potential of eco-friendly, bio-inspired surface engineering to improve the biological performance of titanium-based implants.

11 August 2025 in Journal of Mechanical Engineering and Manufacturing
Verified
Journal Article
Open access
PDF file
Gustavo Filipe PintoGustavo Filipe Pinto
Gustavo Filipe Pinto
DADavid Almeida
David Almeida
Francisco J. G. SilvaFrancisco J. G. Silva
Francisco J. G. Silva
ESEduardo Luís Trindade da Silva
Eduardo Luís Trindade da Silva
RARicardo Alexandre
Ricardo Alexandre
Andresa BaptistaAndresa Baptista
Andresa Baptista
Driven by the industry’s ongoing pursuit of continuous improvement in machining processes, the need to meet environmental targets, and the limited number of scientific studies addressing coatings doped with Tantalum (Ta), were the main motivations to undertake this investigation. This study investigates the impact of coating cutting tools with a TiAlTaN film deposited at two different bias voltages, −90 V and −135 V, and its relationship with cutting forces, surface roughness, and overall performance when machining AISI P20 steel. The choice of AISI P20 steel was deliberate, considering its widespread use in the mould manufacturing industry and the machining challenges posed by its mechanical properties. Throughout the study, during the machining process, the cutting forces in the three axes were measured, as well as the surface roughness of the AISI P20 steel after machining. A correlation was made between the cutting forces obtained and the roughness of the machined surface, considering the coated tools using bias of −90 V and −135 V. The results show that increasing bias level during the coating deposition has a positive effect on the tool machining performance. Also, there was a correlation between the cutting forces during the machining process and the surface roughness of the machined AISI P20 steel. The coated tool with −135 V bias induced lower cutting forces, in line with the lower roughness shown on the machined surface, when compared to the coated tool with −90 V bias.

11 February 2026 in Journal of Mechanical Engineering and Manufacturing
Verified
Journal Article
Open access
PDF file
Luis Miguel DuraoLuis Miguel Durao
Luis Miguel Durao
APAndré Filipe Varandas Pedroso
André Filipe Varandas Pedroso
RMRui Martinho
Rui Martinho
MBMarlene Brito
Marlene Brito
RARicardo Alexandre
Ricardo Alexandre
Angelos MarkopoulosAngelos Markopoulos
Angelos Markopoulos
Injection Moulding (IM) tools play a decisive role in high-volume manufacturing, particularly in the production of polymer components where dimensional accuracy, surface integrity, and process stability are paramount. The increasing adoption of fibre-reinforced polymers (FRPs), especially within the automotive and aerospace sectors, has substantially intensified the mechanical, thermal, and tribological demands imposed on tooling systems, thereby accelerating Tool Wear (TW) and surface degradation. Comparable challenges are encountered in related forming processes, including sheet-metal stamping and pressing, where abrasive contact, cyclic loading, and elevated temperatures contributepractical to premature tool failure. Extending tool service life has consequently emerged as a strategic priority for improving cost efficiency, reducing unplanned downtime, and ensuring consistent product quality across extended production runs. Against this background, the present review critically evaluates recent technological advances aimed at enhancing the durability and operational longevity of injection moulding tools, with a particular focus on solutions that have demonstrated practical relevance under industrial conditions. Advanced surface-engineering approaches, including electrodeposition, nitriding, and physical and chemical vapour deposition (PVD and CVD) coatings, are examined in terms of their effectiveness in mitigating wear, corrosion, and thermal-fatigue damage. Developments in tool material selection, encompassing high-performance alloys and engineered coating systems, are assessed with respect to friction reduction and thermal management, providing actionable insights for tool designers and manufacturing engineers. In addition, the integration of additive manufacturing for tool repair and refurbishment is discussed as a pragmatic and increasingly viable route to extending Tool Lifespan (TL), supporting more sustainable and cost-effective tooling strategies in modern manufacturing environments.

12 June 2025
Verified
Book Chapter
Closed access
PDF file
APAndré Filipe Varandas Pedroso
André Filipe Varandas Pedroso
Francisco J. G. SilvaFrancisco J. G. Silva
Francisco J. G. Silva
Raul CampilhoRaul Campilho
Raul Campilho
RARicardo Alexandre
Ricardo Alexandre
Luis Miguel DuraoLuis Miguel Durao
Luis Miguel Durao