This study presents a novel, eco-friendly synthesis route for zinc oxide (ZnO) nanoparticles using cladode extracts of Hylocereus undatus acting simultaneously as reducing and improving agents, in alignment with green chemistry principles. The synthesis involved the reaction of zinc sulfate heptahydrate with the plant extract, with the medium pH adjusted using sodium hydroxide (NaOH), followed by calcination at 300 °C, 400 °C, and 500 °C, and then by a washing step to enhance purity. Comprehensive characterization was performed using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrical impedance spectroscopy to investigate the structural, morphological, and dielectric properties of the nanoparticles. The sample calcined at 400 °C, followed by washing (HT400W), exhibits highly crystalline ZnO nanoparticles with a predominant wurtzite structure (93.15 wt% ZnO) and minimal impurities (6.85 wt% Na2SO4). SEM analysis indicated a flake-like morphology with nanoscale features (50–100 nm), while Raman spectroscopy confirmed enhanced crystallinity and purity post-washing. Additionally, the HT400W sample exhibited a dielectric constant (ε′) of 16.96 and a low loss tangent (tan δ) of 0.14 at 1 MHz, suggesting superior energy efficiency for high-frequency applications. This green synthesis approach not only eliminates hazardous reagents but also delivers ZnO nanoparticles with good dielectric performance. Furthermore, this work demonstrates the efficacy of a sustainable biotemplate, offering an environmentally friendly approach for synthesizing ZnO nanoparticles with tailored physicochemical properties.
11 August 2025 in Journal of Mechanical Engineering and Manufacturing
Driven by the industry’s ongoing pursuit of continuous improvement in machining processes, the need to meet environmental targets, and the limited number of scientific studies addressing coatings doped with Tantalum (Ta), were the main motivations to undertake this investigation. This study investigates the impact of coating cutting tools with a TiAlTaN film deposited at two different bias voltages, −90 V and −135 V, and its relationship with cutting forces, surface roughness, and overall performance when machining AISI P20 steel. The choice of AISI P20 steel was deliberate, considering its widespread use in the mould manufacturing industry and the machining challenges posed by its mechanical properties. Throughout the study, during the machining process, the cutting forces in the three axes were measured, as well as the surface roughness of the AISI P20 steel after machining. A correlation was made between the cutting forces obtained and the roughness of the machined surface, considering the coated tools using bias of −90 V and −135 V. The results show that increasing bias level during the coating deposition has a positive effect on the tool machining performance. Also, there was a correlation between the cutting forces during the machining process and the surface roughness of the machined AISI P20 steel. The coated tool with −135 V bias induced lower cutting forces, in line with the lower roughness shown on the machined surface, when compared to the coated tool with −90 V bias.
Among the vast array of technologies available for surface modification of materials, sputtering emerges as one of the most versatile methods through coating deposition. Included in the family of physical vapor deposition (PVD) techniques, sputtering allows the production of coatings with a great variety of characteristics, based on a bottom-up approach that forms coatings from individual species (atoms or ions). This versatility is achieved by controlling: (i) the layer architecture, from monolithic to multilayers, (ii) the structures, from amorphous to nanocrystalline or nanocomposite, until highly crystallized, including epitaxial; (iii) the morphologies, from very porous through columnar or zig-zag to very dense and featureless; (iv) the chemical composition, allowing the deposition of metallic, polymeric, ceramic or composite materials types. In this paper, after a brief introduction of sputtering as a deposition technology, we will review the application of sputtering for depositing protective coatings to which an extra functionality is provided: (a) aesthetic color; (b) high-temperature lubrication; and (c) temperature sensing ability.
9 February 2026 in Journal of Mechanical Engineering and Manufacturing
The continuous technological evolution of industry has intensified the role of machining processes, directly influencing product quality and industrial demands. Research in this field has long focused on friction during machining and the benefits of coatings in reducing energy consumption, improving workpiece quality, and extending tool life. Coated tools have been developed to overcome critical challenges, including thermal stability, corrosion resistance at elevated temperatures, and wear resistance under high speed machining. To meet these requirements, coating technologies have advanced, with methods such as CVD, PVD, and hybrid deposition gaining prominence. However, systematic evaluations of the performance evolution of TiAlN-based coatings doped with additional elements still require some attention from researchers. This review addresses that gap by examining the development of TiAlN coatings doped with elements like Mo, Si, Y, Ta, and Cr, as well as their combinations. It also discusses deposition techniques, thin film technologies, and their influence on coating performance. Finally, the paper outlines current trends, future research opportunities, and open challenges, providing insights relevant to both academy and industry.
Industrial water electrolysis systems for hydrogen production use noble metal-based RuO2/IrO2 to catalyze the oxygen evolution reaction (OER). Replacing noble metal compounds with earth-abundant NiFe compounds requires a scalable synthesis technique with structural and morphological control. In this study, DC magnetron sputtering was systematically investigated as a scalable approach for synthesizing NiFe bimetallic thin-film electrocatalysts as alternatives to noble metal-based materials. NiFe thin films (~200 nm) with varying Fe contents were deposited on SS-316L substrates and characterized using compositional, morphological, structural, and electrochemical techniques. Scanning electron microscopy revealed a columnar morphology, while X-ray diffraction confirmed the formation of a NiFe random solid solution. The Fe ratio was found to strongly influence OER performance, with the Fe24Ni76 composition exhibiting the best activity, requiring an overpotential of 361 mV vs. RHE to achieve 10 mA · cm−2 and delivering a current density of 363 mA · cm−2 at 1.7 V vs. RHE. X-ray photoelectron spectroscopy indicated that the enhanced activity of Fe24Ni76 originated from increased oxidation of metallic Ni and a higher density of catalytically active oxide species. These results demonstrate that sputtered NiFe thin films, particularly at optimized compositions, are promising scalable and low-cost OER electrodes for next-generation water electrolysis systems.