Bingyang Ma

Dr. Bingyang Ma

School of Materials Science and Engineering, Shanghai Dianji University, Shanghai 201306, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 February 2020 in Materials
Verified
Journal Article
Open access
PDF file
XQXiaoben Qi
Xiaoben Qi
HSHailong Shang
Hailong Shang
Bingyang MaBingyang Ma
Bingyang Ma
RZRulin Zhang
Rulin Zhang
LGLeyang Guo
Leyang Guo
BSBo Su
Bo Su
The interaction effect of micro arc oxidation (MAO) parameters on the microstructure and wear properties was investigated. The results showed that the electric current and oxidation time significantly influenced the thickness and grinding crack width of the ceramic coatings within the range of the selected parameters, and the interaction effect of the electrical parameters was not obvious. The surface morphology, cross-section morphology, and element distribution of the coatings were observed using scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The results showed that ceramic coatings with γ-Al2O3 and α-Al2O3 formed, which enhanced the coating performance. After that, the microhardness and wear resistance were tested. Under the optimal process, the microhardness of a coating section was up to 1200 HV0.1, and the friction coefficient was just 0.3. When wear occurred, the volcanic microstructures experienced extrusion and deformation, and then peeled off under shear stress, which led to the formation of a grinding crack. The main failure modes of the micro arc oxidation coatings were abrasive wear and spalling failure.

22 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
YLYang Li
Yang Li
HSHailong Shang
Hailong Shang
Bingyang MaBingyang Ma
Bingyang Ma
XGXuqiang Guo
Xuqiang Guo
RLRongbin Li
Rongbin Li
GLGeyang Li
Geyang Li
Two kinds of Al2O3 ceramic samples with and without Al film deposited were designed respectively. The influences of temperature and high kinetic energy sputtering particles on the wettability and interface strength of Al/Al2O3 were studied by comparing the wetting behavior of molten aluminum on two samples. The results show that molten aluminum does not wet the Al2O3 sample without Al film deposited at 700 °C, the contact angle is 165°, and the interfacial shear strength is 28 MPa. With the increase of temperature, the contact angle decreases continuously, and the interface shear strength gradually increases. The fracture of the brazed joint is transferred from the interface to the brazing seam. In comparison, the sample deposited with Al film is wetted by molten aluminum at 700 °C, and the contact angle is only 12°. The interface shear strength is about 120 MPa and is less affected by temperature. The shear fracture of the joint occurs in the brazed seam of Al metal. Therefore, the high energy generated by either the temperature increase or the particle sputtering enable the Al atoms to overcome the energy barrier to form Al–O bonds with the O atoms on the Al2O3 ceramic surface, thereby improving the wettability of Al/Al2O3.

8 February 2024 in Crystals
Verified
Journal Article
Open access
PDF file
YWYing Wang
Ying Wang
Bingyang MaBingyang Ma
Bingyang Ma
Wei LiWei Li
Wei Li
Peter LiawPeter Liaw
Peter Liaw
SYSongpu Yang
Songpu Yang
NZNing Zhong
Ning Zhong
High-entropy alloys (HEAs) have been attracting growing interest for decades due to their unique properties. Electrodeposition provides a low-cost and convenient route for producing classified types of HEAs, compared to other synthesis techniques, making it an attention-grabbing method. However, fabricating high-quality HEAs through electrodeposition in aqueous electrolytes remains a great challenge. In this study, the effects of additives and current densities on the compositions, surface morphologies, microstructures, and corrosion behavior of the electrodeposited NiFeCoCu alloy are studied. The results indicate that saccharin plays a key role in achieving a flat and bright surface for NiFeCoCu coatings, while also relieving the internal stress and improving anti-corrosion properties. Electrodeposition under a current density of 20–40 mA/cm2 results in a uniform and dense deposit with favorable properties. The present work provides a low-cost and feasible industrial solution for the preparation of HEA coatings, which holds great potential for innovation in the field of HEA coatings through electrodeposition.

6 November 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Bingyang MaBingyang Ma
Bingyang Ma
HYHaitian Yuan
Haitian Yuan
ZHZongqian He
Zongqian He
HSHailong Shang
Hailong Shang
YHYanjie Hou
Yanjie Hou
Filipe FernandesFilipe Fernandes
Filipe Fernandes
In this paper, TiN-Ni nanostructured composite films with different Ni contents are prepared using the magnetron sputtering method. The composition, microstructure, and mechanical properties of composite films are analyzed using an X-ray energy spectrometer (EDS), a scanning electron microscope (SEM), X-ray diffraction technology (XRD), a transmission electron microscope (TEM), and nanoindentation. All the films grow in a columnar crystal structure. There are only TiN diffraction peaks in the XRD spectrum, and no diffraction peaks of Ni and its compounds are observed. The addition of the Ni element disrupts the integrity of TiN lattice growth, resulting in a decrease in the grain size from 60 nm in TiN to 25 nm at 20.6% Ni. The film with a Ni content of 12.4 at.% forms a nanocomposite structure in which the nanocrystalline TiN phase (nc-TiN) is surrounded by the amorphous Ni (a-Ni) phase. The formation of nc-TiN/a-Ni nanocomposite structures relies on the good wettability of Ni on TiN ceramics. The hardness and elastic modulus of the film gradually decrease with the increase in Ni content, but the toughness is improved. The hardness and elastic modulus decrease from 19.9 GPa and 239.5 GPa for TiN film to 15.4 GPa and 223 GPa at 20.6 at.% Ni film, respectively, while the fracture toughness increases from 1.5 MPa·m1/2 to 2.0 MPa·m1/2. The soft and ductile Ni phase enriched at the TiN grain boundaries hinders the propagation of cracks in the TiN phase, resulting in a significant increase in the film’s toughness. The research results of this paper provide support for the design of TiN-Ni films with high strength and toughness and the understanding of the formation mechanism of nanocomposite structures.

5 April 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZRZhun Ran
Zhun Ran
HSHailong Shang
Hailong Shang
Bingyang MaBingyang Ma
Bingyang Ma
RLRongbin Li
Rongbin Li
FSFujun Shangguan
Fujun Shangguan
DYDayi Yu
Dayi Yu
This paper presents a magnetron sputtering Al/Cu bilayer film solder to realize the brazing of AlN ceramic and Al metal. The effect of different temperatures on the structure and mechanical properties of brazed joints is studied. The results show that the sputtered Al particles have a sputtering wetting effect on AlN ceramic. The contact angle of molten Al on AlN ceramic with Al film deposited at 700 °C is as low as about 30°. While the contact angle of molten Al on AlN ceramic without Al film deposited at 1000 °C is about 89°. There is a large amount of Cu enrichment in brazed joints at 600 °C. The weld structure is a mixture of Al solid solution and AlCu compound. The shear strength of the brazed joint is only 70.6 MPa, and the joint fracture shows a large number of brittle fracture morphologies. With the increase of brazing temperature, the phenomenon of Cu enrichment in the joint gradually weakens, and the weld structure gradually transforms into a solid solution of Cu in Al. The shear strength of the brazed joint continues to increase, and the joint fracture morphology gradually changes from brittle fracture to furrow-like plastic fracture morphology. When the brazing temperature is increased to 660 °C, the distribution of Cu in the joint is evenly dispersed, and the shear strength of the brazed joint reaches the highest value of 107.8 MPa. The joint fracture is completely furrow-like plastic fracture morphological composition.

1 March 2021 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
Bingyang MaBingyang Ma
Bingyang Ma
XQXiaoben Qi
Xiaoben Qi
RLRongbin Li
Rongbin Li
RZRulin Zhang
Rulin Zhang
HSHailong Shang
Hailong Shang