Showmik Ahsan

Dr. Showmik Ahsan

Materials Science and Engineering, Wright State University, Dayton, Kentucky, USA
orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 November 2025 in Materials & Design
Verified
Journal Article
Open access
SDSatyavan Digole
Satyavan Digole
MGMayank Garg
Mayank Garg
SBSmriti Bohara
Smriti Bohara
FTFu-Yan Tsai
Fu-Yan Tsai
SAShowmik Ahsan
Showmik Ahsan
TBTushar Borkar
Tushar Borkar

23 December 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SKSambhaji Kusekar
Sambhaji Kusekar
PDPrashant Dhondapure
Prashant Dhondapure
MJMohammad Jahazi
Mohammad Jahazi
SAShowmik Ahsan
Showmik Ahsan
HYHenry Young
Henry Young
TBTushar Borkar
Tushar Borkar

27 August 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
SKSanoj Karki
Sanoj Karki
MGMayank Garg
Mayank Garg
CSCaleb Schenck
Caleb Schenck
FTFu-Yun Tsai
Fu-Yun Tsai
MLMichael Lastovich
Michael Lastovich
TBTushar M. Borkar
Tushar M. Borkar

27 October 2025 in Materials
Verified
Journal Article
Open access
PDF file
Sambhaji K KusekarSambhaji K Kusekar
Sambhaji K Kusekar
JEJames Elder
James Elder
JDJay Desai
Jay Desai
SAShowmik Ahsan
Showmik Ahsan
HYHenry Young
Henry Young
Tushar BorkarTushar Borkar
Tushar Borkar
Forging plays a crucial role in various industries, including aerospace, automotive, oil and gas, and defense. We investigated the effect of post-processing forging on microstructural and mechanical properties of 316L stainless steel forging preforms fabricated by laser powder bed fusion. The as-built samples were subjected to hot forging in order to refine the microstructure and enhance mechanical performance. Detailed characterization was performed using Electron Backscatter Diffraction, Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Tensile testing, and Hardness Testing. Substantial grain refinement (up to 97%) was observed, in addition to a reduction in porosity. The forging process effectively transformed the columnar grain morphology into equiaxed grains, increased yield and ultimate tensile strengths of 560 MPa and 740 MPa, representing 27% and 32% improvements, respectively, with a corresponding decrease in elongation to 32% from 47%. The horizontally built samples achieved the highest yield strength of 605 MPa but slightly lower UTS 710 MPa, representing 32% and 5% increment and decrease in ductility to 28% from 37.5%. These trends reflect the combined effects of work hardening and grain refinement, which enhance strength at the expense of ductility.

16 May 2026 in Materials Science and Engineering: A
Verified
Journal Article
Open access
Sambhaji K KusekarSambhaji K Kusekar
Sambhaji K Kusekar
JDJay Desai
Jay Desai
ACAmit Choudhari
Amit Choudhari
SAShowmik Ahsan
Showmik Ahsan
HYHenry Young
Henry Young
TBTushar Borkar
Tushar Borkar

2 November 2026 in Advances in Mechanical Engineering
Verified
Journal Article
Open access
JTJeet Bahadur Thapa
Jeet Bahadur Thapa
VAVignesh Asam
Vignesh Asam
SAShowmik Ahsan
Showmik Ahsan
FSFuzail Shad
Fuzail Shad
HYHenry Young
Henry Young
AMAhsan Mian
Ahsan Mian
Selective laser sintering (SLS) produces functional polymer components with complex geometries, yet the compressive behavior of printed parts across build orientations and strain rates remains sparsely documented. This study examines how build orientation and strain rate affect the compression response of glass bead-filled polyamide 12 (PA12-GF) printed on a Formlabs Fuse 1 using a fixed unidirectional scan strategy. Cylindrical specimens conforming to ASTM D695 (12.7 mm diameter, 25.4 mm length) were compressed to 50% engineering strain in seven build orientations ( X , Y , Z , D xy , D xz , D yz , D xyz ) at four strain rates (0.01, 1, 3, and 5 s −1 ). Compressive modulus and 0.2% offset yield stress were obtained from the stress-strain curves using adaptive toe compensation followed by ordinary least-squares regression. Microstructure was characterized by X-ray diffraction (XRD) for the crystalline phase, scanning electron microscopy (SEM) for bead morphology and interfacial bonding, density measurements using Archimedes and geometric methods. X-ray computed tomography (XRCT) was used to estimate the volumetric glass fraction. PA12-GF shows a clear stiffness-strength trade-off under compression, with the compressive modulus reaching 1.51 to 2.18 GPa while the yield stress remains within 41.0 to 61.7 MPa across all orientations and strain rates. SEM observations suggest that early yielding is associated with stress concentrations at the bead–matrix interface, as evidenced by debonding gaps and bead pullout craters on the fracture surface. The presence of glass beads alters the orientation response by providing additional load-transfer pathways across hatch boundaries, while interlayer interfaces remain the weaker load path in the build direction. Over the tested range, the modulus of elasticity increases with strain rate in all orientations, whereas the yield stress peaks near 3 s −1 before declining at 5 s −1 in most orientations. This behavior is consistent with local thermal softening from plastic-work heating, although other rate-dependent mechanisms may also contribute to the observed softening, including bead-matrix debonding. These results provide an orientation- and strain-rate-dependent compressive dataset and a microstructure-based framework for understanding the mechanical response of SLS-printed PA12-GF components.