Timely detection of leaks is essential for the safe and reliable operation of pressure vessels used in superconducting systems, aerospace, and medical equipment. To address the lack of efficient online leak detection methods for such vessels, this paper proposes a quasi-distributed fiber Bragg grating (FBG) sensing network combined with theoretical stress analysis to diagnose vessel conditions. We analyze the stress–strain distributions of vacuum vessels under varying pressures and examine stress concentration effects induced by small holes; these analyses guided the design and placement of quasi-distributed FBG sensors around the vacuum valve for online leakage monitoring. To improve measurement accuracy, we introduce a vibration correction algorithm that mitigates pump-induced vibration interference. Comparative tests under three leakage scenarios demonstrate that when leakage occurs during vacuum extraction, the proposed system can reliably detect the approximate leak location. The results indicate that combining an FBG sensing network with stress concentration analysis enables initial localization and assessment of leak severity, providing valuable support for the safe operation and rapid maintenance of vacuum pressure vessels.
Carbon fiber-reinforced polymer (CFRP) composites are increasingly used in aerospace, rail transportation, and energy engineering owing to their high specific strength and corrosion resistance. However, their complex and interacting damage mechanisms, including delamination and matrix cracking, present significant challenges for reliable structural health monitoring. Fiber Bragg grating (FBG) sensors offer distinct advantages for monitoring composite structures because of their compact size, immunity to electromagnetic interference, embeddability, and capability for distributed strain measurement. Nevertheless, the effectiveness of an FBG sensing network depends strongly on the spatial distribution of the sensing points. This study proposes a finite-element-assisted framework for evaluating and improving FBG sensor layouts for strain-field reconstruction and structural feature characterization of composite plates. The framework first reconstructs the spatial strain field from limited sensing data using interpolation and least-squares fitting methods, and then evaluates the performance of existing and candidate sensor layouts based on reconstruction errors and spatial coverage of structurally important regions. A strain-gradient-informed heuristic strategy is subsequently developed to improve sensor placement by combining high-gradient region identification, spatially uniform coverage, minimum-distance constraints, and predefined support-region monitoring requirements. The Fourier least-squares fitting method provides the lowest reconstruction error among the investigated approaches and is therefore adopted for subsequent layout evaluation and improvement. Finite-element simulations and experimental measurements are used to assess the reconstruction performance and identify the advantages and limitations of different sensor layouts under static and dynamic loading conditions. The results demonstrate that the proposed framework can effectively evaluate existing FBG layouts and provide a systematic basis for their improvement, while also revealing the trade-off between local strain-gradient resolution and global spatial coverage. The proposed framework provides practical guidance for the performance-oriented design and improvement of FBG sensor networks for structural health monitoring of composite structures.
The influence of mechanical noise on impact identification using fiber Bragg grating (FBG) accelerometers in complex environments remains insufficiently explored and quantitatively characterized. This study investigates how the intensity and propagation path of mechanical noise affect the output stability and impact-detection capability of a self-developed FBG accelerometer. A quantitative evaluation approach is established using wavelength-variation statistics, impact-response amplitude, and signal-to-noise ratio (SNR). Experimental results show that mechanical noise markedly increased the background wavelength fluctuation, with the maximum standard deviation reaching 16.71 pm, approximately 11 times the no-additional-noise value. By contrast, the RMS of the target impact response increased only slightly, from 0.0300 nm to 0.0353 nm, indicating that mechanical noise primarily affects baseline stability rather than the amplitude of the target impact response. Under the highest-intensity disturbance tested, the SNR remained at 22.98 dB, and the impact event remained distinguishable. The proposed multi-indicator approach provides a quantitative characterization of the FBG accelerometer response under different mechanical-noise conditions. A commercial 941B accelerometer was used as an external reference for sensitivity calibration, and its measurements were not used for direct performance comparison with the FBG accelerometer. The results provide experimental evidence of the impact-identification behavior of the proposed sensor under the investigated mechanical-noise conditions.
Internal responses of multilayer pavement structures are difficult to characterize using surface-based inspection alone. This study investigates a scaled multilayer pavement model instrumented with embedded quasi-distributed fiber Bragg grating (FBG) sensing lines to obtain baseline internal strain responses and FBG-derived relative vertical displacement distributions under controlled loading. Central single-point stepwise loading, symmetric two-point loading, and asymmetric two-point loading were applied, and FBG wavelength responses were converted into temperature-compensated strain and then into line-wise relative vertical displacement through strain–curvature conversion, curvature integration, and linear baseline correction. During loading, the ambient temperature ranged from 22.70 to 23.40 °C, and the maximum relative shift of the T-sensor was 0.008297 nm. Under 686 N central loading, SAL1 reached a maximum temperature-compensated strain of 1459.39 με and a maximum relative vertical displacement of 1.079 mm, whereas SAL2 reached 793.13 με and 0.583 mm. Under approximately 490 N asymmetric two-point loading, SAT2 reached 1699.48 με and 0.761 mm. Soil-base responses were substantially lower. Because no independent displacement measurement was acquired, the reconstructed quantity is interpreted as an FBG-derived relative deformation measure rather than an absolute displacement. The results establish intact baseline data for future, separately validated comparisons with abnormal conditions.