The technical and economic efficiency of new PCMs depends on the ability to predict their performance. The problem of predicting the properties of PCMs can be solved by computer simulation by the finite element method. In this work, an experimental determination of the physical and mechanical properties of PTFE PCMs depending on the concentration of fibrous and dispersed filler was carried out. A finite element model in ANSYS APDL was built to simulate the strength and load-bearing capacity of the material with the analysis of damage accumulation. Verification of the developed computer model to predict the mechanical properties of composite materials was performed by comparing the results obtained during field and model experiments. It was found that the finite element model predicts the strength of chaotically reinforced spherical inclusions of composite materials. This is due to the smoothness of the filler surfaces and the lack of filler dissection in the model. Instead, the prediction of the strength of a finite element model of chaotically reinforced cylindrical inclusions of composite materials requires additional analysis. The matrix and the fibrous filler obviously have stress concentrators and are both subject to the difficulties of creating a reliable structural model.
Composite materials have a wide range of functional properties, which is ensured by using various technological methods of obtaining both the matrix or fillers and the composition as a whole. A special place belongs to the composition formation technology, which ensures the necessary structure and properties of the composite. In this work, a computer simulation was carried out to identify the main dependencies of the behavior of composite materials in the process of the main technological operations of their production: pressing and subsequent sintering. A polymer matrix randomly reinforced with two types of fillers: spherical and short cylindrical inclusions, was used to construct the finite element models of the structure of composites. The ANSYS Workbench package was used as a calculation simulation platform. The true stress–strain curves for tension, Poisson’s ratios, and ultimate stresses for composite materials were obtained using the finite element method based on the micromechanical approach at the first stage. These values were calculated based on the stretching diagrams of the matrix and fillers and the condition of the ideality of their joint operation. At the second stage, the processes of mechanical pressing of composite materials were modelled based on their elastic–plastic characteristics from the first stage. The result is an assessment of the accumulation of residual strains at the stage before sintering. The degree of increase in total strain capability of composite materials after sintering was shown.
This article is devoted to modeling, researching and optimizing the main properties of an environmentally clean polymer composition based on oligofurfuryloxysiloxanes (OFOS), which can be used to produce casting molds and cores in the production of castings from ferrous and nonferrous metals. Polymer compositions were examined for strength, survivability, gas permeability, moisture, crumbliness, fire resistance, knockout, and stickability. It has been established that the increase in the strength of the polymer composition over time obeys an exponential law. Mathematical equations were derived for all the exponential curves. The indications of compressive strength of the polymer composition with OFOS with all the acid catalysts used were, on average, as follows: after 1 h—1.3–1.54 MPa; after 3 h—2.5–2.9 MPa; after 24 h—4.9–6.1 MPa, which meets the requirements for casting molds before pouring with metal. The use of polymer compositions with OFOS ensures environmental safety of the technological process, due to the lack of emission of toxic substances, both in the “cold” stage of the process and during casting with molten metal, cooling, knocking out, and disposal of polymer compositions. This makes it possible to save energy resources, and thereby reduce the total cost of the entire technological process and castings.
2 February 2022 in Continuum Mechanics and Thermodynamics
This paper is oriented toward the specific testing of polymer composites and textile PA66 cords used as reinforcement for composites. The aim of the research is to validate the proposed new testing methods for low-cyclic testing of polymer composites and PA66 cords for the characterization of material parameters useful as input data for computational tire simulations. Part of the research is the design of experimental methods for polymer composites and test parameters such as load rate, preload, and other parameters such as strain for the start and stop of cycle steps. The DIN 53835-13 standard is used for the conditions of textile cord during the first five cycles. A cyclic load is carried out at two temperatures of 20 °C and 120 °C. The testing method includes a hold step for 60 s between each loop. The video-extensometer technique is used for testing. The paper evaluated the effect of temperatures on the material properties of PA66 cords. The true stress-strain (elongation) dependences between points for the video-extensometer of the fifth cycle of every cycle loop are the data results from composite tests. The forcestrain dependences between points for the video-extensometer are the data results from tests of the PA66 cord. These dependencies can be used as input material data of textile cords in the computational simulation of tire casings using a custom material model definition. The fourth cycle in every cycle loop of polymer composites can be considered a stable cycle because the change in the maximum true stress between the fourth and fifth cycles is 1.6%. Other results of this research include a relationship between stress and the number of cycle loops as the second-degree polynomial curve for polymer composites and a simple relationship to describe the value of the force at each end of the cycles for a textile cord.
7 January 2025 in Advanced Composites and Hybrid Materials
Finding a way to increase the amount of recycled waste tyres is a current global challenge. Among others, the production of ground tyre rubber (GTR) and its application in a new rubber compound looks as a perspective way. However, the compatibility of GTR and rubber matrix is limited, leading to insufficient properties of the new material. To improve them, it is suitable to activate the GTR prior to mixing. In this paper, GTR obtained by water jet process was activated with microwave irradiation (i) in a household oven at 400 W and 800 W for 1 and 3 min, and (ii) in an industrial device at 500 W, 1000 W, 1500 W and 1750 W for 1, 3 and 5 min. A total of 7% (w/w) of the irradiated GTR was incorporated into a carbon black-filled rubber compound based on styrene-butadiene rubber (SBR), natural rubber (NR) and butadiene rubber (BR), with a formulation for off-road tyre treads. Most compounds containing microwave-treated GTR showed comparable or better properties than the reference with untreated GTR (tensile strength, 14.9 MPa; elongation at break, 437%; modulus at 300% elongation, 8.97 MPa; hardness, 65.6 Shore A). The industrial microwave device offered better results and the possibility of use of higher variation in conditions than the home microwave oven.