The article presents the microstructure and properties of joints welded using the Hybrid Laser Arc Welding (HLAW) method laser beam-Metal Active Gas (MAG). The joints were made of 10-mm-thick steel S700MC subjected to the Thermo-Mechanical Control Process (TMCP) and characterised by a high yield point. In addition, the welding process involved the use of solid wire GMn4Ni1.5CrMo having a diameter of 1.2 mm. Non-destructive tests involving the joints made it possible to classify the joints as representing quality level B in accordance with the ISO 12932 standard. Destructive tests of the joints revealed that the joints were characterised by tensile strength similar to that of the base material. The hybrid welding (laser beam-MAG) of steel S700MC enabled the obtainment of good plastic properties of welded joints. In each area of the welded joints, the toughness values satisfied the criteria related to the minimum allowed toughness value. Tests involving the use of a transmission electron microscope and performed in the weld area revealed the decay of the precipitation hardening effect (i.e., the lack of precipitates having a size of several nm) and the presence of coagulated titanium-niobium precipitates having a size of 100 nm, restricting the growth of recrystallised austenite grains, as well as of spherical stable TiO precipitates (200 nm) responsible for the nucleation of ferrite inside austenite grains (significantly improving the plastic properties of joints). The tests demonstrated that it is possible to make welded joints satisfying quality-related requirements referred to in ISO 15614-14.
This article presents the results of research on the development of the technology of laser beam butt welding of 17-4 PH stainless steel sheets and the technology of post-weld heat treatment (PWHT). The developed technology allows for favorable conditions to be obtained and for the appropriate microstructure and hardness to exist in the weld area. Moreover, it enables the fulfillment of a number of specific requirements beyond the possibilities of manual welding and other methods. The tests performed include the analysis of the microstructure with the use of light microscopy (LM) for the materials after welding and PWHT. The applied PWHT showed changes in the microstructure and mechanical properties. In all weld areas the martensitic microstructure was observed. The homogeneity of the microstructure in the area of the welded joint after PWTH was revealed. In the as-welded condition and after the PWHT with aging at 481 °C, the hardness was 440 HV5, but after aging at 621 °C, it decreased to 330–340 HV5.
This work presents the results of the comparison between simulations and experiments of the laser welding of advanced multiphase steel. The numerical simulations of welding with different parameters were carried out using the Sysweld software. The geometry of the weld and structural constituents as well as stress distributions were analyzed. The simulated thermal cycles were incorporated in the JMatPro software to determine the phase transformation kinetics during cooling. The experimental tests were performed to compare the simulations with the real results. According to them, the shape of the weld and its width were symmetrical according to the weld axis. The simulated values were higher compared to the real one at heat inputs higher than 0.048 kJ/mm. The microstructure investigations conducted with scanning electron microscopy showed a good agreement in the fusion zone. Some differences in the microstructure of heat-affected zone and transition zone were identified. According to the phase transformation simulations, the weld should be composed of only martensite. The real microstructure was composed of martensite and some fraction of bainite in the heat affected zone. The more complex microstructure consisting of ferrite, bainite and retained austenite was present in the transition zone. The results of measured and simulated hardness indicated the good agreement with the difference of 17 HV0.1.
This study discusses the effect of laser beam welding parameters on the structure, mechanical properties and corrosion resistance of 1.2 mm thick galvanized sheets made of low-carbon steel DC04 provided with a ZE36/36 GardoprotectOC2BU organic coating. The test laser beam butt welded joints were made without the filler metal, using a variable welding rate, where linear welding energy was restricted within the range of 30 J/mm to 90 J/mm. The joints were subjected to non-destructive tests, destructive tests and corrosion resistance tests. The tests revealed the possibility of making joints meeting the criteria specified in the ISO 15614-11 standard. Regardless of the value of linear welding energy applied in the process, all the joints were characterised by high mechanical and plastic properties. It was noticed that an increase in linear welding energy from 30 J/mm to 90 J/mm was accompanied by the widening of the weld and that of the heat-affected zone (HAZ). In addition, an increase in linear welding energy was accompanied by a decrease in the maximum weld hardness to approximately 250 HV0.2. In the HAZ, hardness was restricted within the range of 190 HV0.2 to 230 HV0.2 and decreased along with increasing linear welding energy. In the static tensile test, regardless of the value of linear welding energy, the test specimen ruptured in the base material. In the bend test, regardless of the value of linear welding energy, a bend angle of 180° was obtained without partial tear or scratches; unit elongation was restricted within the range of 29% to 42%. The electrochemical tests and experiments performed in the salt spray chamber revealed the very high effectiveness of the corrosion protections against aggressive chloride ions.
The paper presents a numerical model based on the finite element method (FEM) to predict deformations and residual stresses in socket welding of different diameter stainless steel pipes made of X5CrNi18-10 steel. The next part of the paper concerns the determination of strength properties of a welded joint in terms of a shear test. A thermo-elastic–plastic numerical model is developed using Abaqus FEA software in order to determine the thermal and mechanical phenomena of the welded joint. This approach requires the implementation of moveable heat source power intensity distribution based on circumferentially moving Goldak’s heat source model. This model is implemented in the additional DFLUX subroutine, written in Fortran programming language. The correctness of the assumed model of thermal phenomena is confirmed by examinations of the shape and size of the melted zone. The strength of the welded joint subjected to shear is verified by performing a compression test of welded pipes as well as computer simulations with validation of the computational model using the Dantec 3D image correlation system.