Four compositions of rapidly quenched ribbon brazing alloys based on Ag–Cu–Ti (Ag–26.5Cu–1.5Ti, Ag–25Cu–5Ti) and Ag–Cu–Zr (Ag–26.5Cu–1.5Zr, Ag–25Cu–5Zr) systems were produced. Initial ingots were synthesized by arc melting. Rapidly solidified ribbons, 50–100 μm thick, were then fabricated from homogenized ingots using a “Crystall-702” facility. A comparative analysis of the microstructure and phase composition of both the ingots and ribbons was conducted using scanning electron microscopy and X-ray diffraction. The analysis revealed the presence of Cu4Ti and CuTi intermetallic compounds in the Ag–Cu–Ti alloys, and AgCu4Zr and Zr2Cu in the Ag–Cu–Zr alloys. Rapid quenching was found to produce metastable structures and significantly refine the intermetallic phases. Microhardness measurements of the ingot and ribbon states demonstrated a substantial influence of the processing route on the mechanical properties. The tensile strength of the ingots was also evaluated. The wetting angles of the rapidly quenched alloy melts on 99% Al2O3 (alumina) ceramic substrates under vacuum were determined. All produced ribbons, except for the Ag–26.5Cu–1.5Zr composition, demonstrated adequate wettability. Thus, these materials are considered promising for further research into heat-resistant metal–ceramic joints.
Four compositions of rapidly quenched ribbon brazing alloys based on the Ag-Cu-Ti (Ag-26.5Cu-1.5Ti, Ag-25Cu-5Ti) and Ag-Cu-Zr (Ag-26.5Cu-1.5Zr, Ag-25Cu-5Zr) sys-tems were produced. Initial ingots were synthesized by arc melting. Rapidly solidified ribbons, 50-100 μm thick, were then fabricated from homogenized ingots using a "Crystall-702" facility. A comparative analysis of the microstructure and phase com-position of both the ingots and ribbons was conducted using scanning electron mi-croscopy and X-ray diffraction. The analysis revealed the presence of Cu4Ti and CuTi intermetallic compounds in the Ag-Cu-Ti alloys, and AgCu4Zr and Zr2Cu in the Ag-Cu-Zr alloys. Rapid quenching was found to produce metastable structures and significantly refine the intermetallic phases. Microhardness measurements of the ingot and ribbon states demonstrated a substantial influence of processing route on me-chanical properties. The tensile strength of the ingots was also evaluated. Wetting an-gles of the rapidly quenched alloy melts on 99% Al2O3 (alumina) ceramic substrates under vacuum were determined. All produced ribbons, except for the Ag-26.5Cu-1.5Zr composition, demonstrated adequate wettability. Thus, these materials are considered promising for further research into heat-resistant metal-ceramic joints.
Amorphous ribbon brazing filler metals produced by rapid melt quenching form a distinct class of high-temperature brazing materials; a few ductile microcrystalline ribbons are treated as boundary cases. This review systematizes the four industrial families of such fillers: copper–phosphorus (Cu–Ni–Sn–P), titanium (Ti–Cu–Ni, Ti–Zr–Cu–Ni(–Be)), zirconium (Zr–Ti–Cu–Ni, Zr–Cu–Fe–Be), and nickel–metalloid (Ni–Cr–Si–B, Ni–Cr–P) alloys, together with the closely allied iron-based fillers. This selection is no accident: to become the basis of a commercial filler metal, an amorphous alloy must simultaneously satisfy five criteria (C1–C5) of brazing temperature, glass formation, base-material compatibility, ribbon manufacturability, and cost and safety, which are formulated here as a single cross-system checklist with operational thresholds. The class itself exists because in deep eutectics, the depressant and glass-former functions can coincide. Transient liquid phase (TLP) bonding, for which the thin homogeneous ribbon is a particularly suitable carrier, runs through the review as a unifying thread. The structural heredity of the ribbon-derived melt and the complementarity of the families by base material are discussed; ductile silver and aluminum fillers serve as a negative control delineating the boundary of the class, and the criteria are applied predictively to compare the families and to select a filler metal for a specific task.