The time-interleaved analog-to-digital converter has shown to be a key component of the latest ultra-wide band systems. Unfortunately, the sub-analog-to-digital converters are prone to parameter deviations caused by process-voltage-temperature, which can affect the output linearity. This article presents a foreground time-interleaved analog-to-digital converter mismatch calibration, which is one of the few available in the literature that can be adapted to any interleaving factor and calibrate overall frequency-dependent mismatches. Moreover, the proposed scheme is highly suited to state-of-the-art transceivers without the need for extra analog expensive circuitry or input signal purity. The foreground signal and correction structure complexity are greatly alleviated due to the developed mismatch detection and genetic algorithm logic. Numerical simulations and measurement results are presented. A commercial 3.6-GS/s time-interleaved analog-to-digital converter was utilized to verify the algorithm performance and experimental issues regarding mixed mismatches are addressed.
22 April 2019 in IEEE Microwave and Wireless Components Letters
This letter presents a dual-band (0.902 and 2.45 GHz) radio frequency (RF)-dc CMOS converter employing the internal threshold voltage cancelation (IVC) technique to harvest electromagnetic energy. The realized RF-dc CMOS converter maintains high power conversion efficiency (PCE) by passively reducing the threshold voltage of the forward-biased transistors so as to increase the harvested power, and increases the threshold voltage of the reverse-biased transistors to reduce the leakage current. More than 20% measured PCE is achieved at 0.902 GHz from -9 to 10-dBm input power range and a peak PCE of 47% is obtained at 1 dBm. At 2.45-GHz band, more than 11% measured PCE is achieved from -2 to 15 dBm input power range and a peak PCE of 27.1% is obtained at 6 dBm. A single-stage RF-dc CMOS converter is realized in 180-nm CMOS technology and it can serve as a good reference to multiband CMOS energy harvesting design in the future.
6 April 2021 in IEEE Transactions on Power Electronics
This article presents a power-efficient hybrid energy-harvesting system that scavenges energy from solar, vibration, and radio frequency (RF) energy sources and converts into regulated output dc voltage courtesy buck–boost dc–dc converter. The proposed architecture incorporates tetra-paths for maintaining high power conversion efficiency (PCE) over extended input power range (−10 to 30 dBm). A time-domain maximum power point tracking technique is proposed for solar energy harvester. A high-efficiency full wave rectifier is designed for triboelectric rectifier. A 5.8-GHz RF-dc converter with adaptive matching is proposed to increase dynamic range of the input power. The chip is implemented in 0.18-µm bipolar-CMOS-DMOS process. The die area of the chip is 2.8 mm × 5.0 mm, including the pads. The solar and triboelectric energy harvesters achieve a measured peak efficiencies of 75.4% and 92.3%, respectively. The high-power 5.8-GHz RF-dc converter achieves measured PCE of 76% at 30 dBm input power. The low-power dual-band RF-dc converter operating at 900 MHz and 2.4 GHz obtains measured peak efficiencies of 73% and 71.9% at 0 dBm input, respectively. The buck–boost dc–dc converter employed in the proposed hybrid energy harvesting system achieves a measured peak PCE of 94.5%.
9 October 2018 in IEEE Transactions on Power Electronics
This paper presents a reconfigurable wide input power range radio frequency (RF) energy harvester (EH) with alliance for wireless power (A4WP) wireless power receiver (WPR). A reconfigurable RF-DC converter for RF EH and maximum power point tracking algorithm are proposed to maintain high efficiency over a wide input power range -20 to +20 dBm. The A4WP WPR is designed and merged with the EH to receive power higher than +20 dBm. In order to improve the power conversion efficiency (PCE), the delay between the ac input voltage and current is compensated by the proposed open-loop delay compensation method. The chip is implemented in 0.18 μm bipolar-CMOS-double-diffused metal-oxide-semiconductor process. The die area of the chip is 4.3 mm × 3.2 mm, including the pads. The proposed EH with WPR achieves a measured peak PCE of 48.19% with respect to the input power of 0 dBm at 900 MHz. It also has a peak PCE of 82.14% with respect to the input power of 30 dBm in an A4WP mode operation at 6.78 MHz.
21 February 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
This paper presents a low-power frequency-shift keying (FSK) transmitter (TX) with an all-digital phase locked loop (ADPLL) based on direct modulation for use in Bluetooth low energy application. A low power ADPLL with a Retimer, 2-stage time to digital converter, and gain estimation technique is proposed to achieve low-power direct FSK modulation at 1 Mbps data rate. A high-efficiency class-D power amplifier, with dual output power modes and a ramping digital filter (RDF), is proposed to reduce the spurious tones. The proposed TX is implemented on 1P6M 55-nm CMOS technology with a die size of 0.53 mm². The phase noise is -119 dBc/Hz at a 1 MHz offset with frequency of 2.44 GHz. TX output power levels of 1.6 and 10 dBm have a power consumption of 3.9 and 18 mW, respectively. The power control ranges for the 1.6 and 10 dBm modes are 25 and 23 dB, respectively. With the RDF, when the output level is +1.6 dBm, the second, and third harmonic distortions at the TX output are -44 and -49 dBm, respectively. The proposed TX achieves an error vector magnitude of 3.48% at an output power level of +1.6 dBm.
In this paper, a low-power reconfigurable ambient Radio Frequency to Direct Current power (RF–DC) converter using an internal threshold voltage cancellation (IVC) scheme with an auxiliary transistors block is presented. A maximum power point tracking (MPPT) algorithm is implemented in order to maintain the high efficiency by automatically selecting the number of stages. The proposed reconfigurable converter efficiently converts the RF signals to DC voltage by dynamically controlling the threshold voltage of the forward and reversed-biased transistors in the primary rectification body. During positive half-cycle, the proposed RF–DC converter reduces the voltage drop across the forward-biased transistors, which results in increased harvested power and output DC voltage. During negative half cycle, the proposed rectifier minimizes the reverse leakage current and prevents the loss of energy stored in the prior stages. A five-stage internal threshold compensated power converter is designed in 0.18 µm Complementary Metal-Oxide-Semiconductor (CMOS) technology with an active die area of 360 µm × 160 µm, while the Maximum Power Point Tracking (MPPT) occupies an active die area of 730 µm × 280 µm. The proposed scheme obtains maximum post-simulated power conversion efficiency (PCE) of 39.3% when input power level is −15 dBm and produces an output voltage of 3.3 V for a load of 1 MΩ and at a frequency of 900 MHz. The proposed scheme achieves a voltage sensitivity of 1V at a remarkably low input power of −21 dBm for a 1 MΩ load.