18 May 2020 in IEEE Transactions on Instrumentation and Measurement
This paper presents a low power, all-digital multichannel Time to Digital Converter (TDC) for Light Detection and Ranging (LiDAR) sensors. The proposed TDC architecture here, measures the time interval through a coarse counter, middle, and fine delay line based interpolation technique (the Nutt method). Automatic calibration by middle and fine All Digital Delay Locked Loops (ADDLL) is provided to ensure the stability of the generated time-slots. Charge pump, loop filter, and voltage-controlled delay line inside the conventional analog Delay Locked Loops (DLL) are replaced by an Accumulator (ACC) and Digitally Controlled Delay Line (DCDL). This makes the design particularly compact, low power, and suitable for multichannel applications. The presented architecture can generate information for amplitude variation (Walk Error) compensation. This information is generated by measuring the pulse width and position of three successive STOP pulses inside each channel within a single-shot measurement. A low-jitter Injection Locked Frequency Multiplier (ILFM) generates 625 MHz internal clock signal out of 25 MHz external reference oscillator, which shrinks the number of delay elements to cover one period of the reference clock and improves the precision of the TDC. Operation at higher frequency provides high throughput and short conversion time (less than 3ns). The three-level TDC offers 13.1 μs maximum input range and 50 ps resolution. The measured DNL and INL of the TDC circuit are 0.47 and 0.71 LSB, respectively. The TDC circuit is implemented in a 180 nm standard CMOS process with a die size of 1.5 mm × 1.5 mm. The total power consumption of the multichannel TDC is 87.6 mW.
6 April 2021 in IEEE Transactions on Power Electronics
This article presents a power-efficient hybrid energy-harvesting system that scavenges energy from solar, vibration, and radio frequency (RF) energy sources and converts into regulated output dc voltage courtesy buck–boost dc–dc converter. The proposed architecture incorporates tetra-paths for maintaining high power conversion efficiency (PCE) over extended input power range (−10 to 30 dBm). A time-domain maximum power point tracking technique is proposed for solar energy harvester. A high-efficiency full wave rectifier is designed for triboelectric rectifier. A 5.8-GHz RF-dc converter with adaptive matching is proposed to increase dynamic range of the input power. The chip is implemented in 0.18-µm bipolar-CMOS-DMOS process. The die area of the chip is 2.8 mm × 5.0 mm, including the pads. The solar and triboelectric energy harvesters achieve a measured peak efficiencies of 75.4% and 92.3%, respectively. The high-power 5.8-GHz RF-dc converter achieves measured PCE of 76% at 30 dBm input power. The low-power dual-band RF-dc converter operating at 900 MHz and 2.4 GHz obtains measured peak efficiencies of 73% and 71.9% at 0 dBm input, respectively. The buck–boost dc–dc converter employed in the proposed hybrid energy harvesting system achieves a measured peak PCE of 94.5%.
18 September 2020 in IEEE Transactions on Power Electronics
In this article, a 15-W quadruple-mode reconfigurable wireless power-receiving unit with high efficiency for Inductive coupling and magnetic resonance-based standards, such as wireless power consortium (WPC), power matters alliance (PMA), alliance for wireless power (A4WP), and magnetic secure transmission (MST) applications is proposed. Quadruple-mode gate controller(QMGC) is proposed in quadruple-mode synchronous rectifier to manage sizes of core and drivers which results in maximum power conversion efficiency (PCE) for each mode based on conduction and switching losses. In QMGC, switchable zero voltage and current sensing block is proposed for WPC/PMA to maximize PCE regardless of load current variations. For A4WP mode, a digitally controlled delay adjustment block is adapted to minimize power consumption while compensating for delay which results in reverse leakage current and power loss. Finally, for MST mode, low power TX (LPTX) block is implemented to minimize current consumption so that burden on battery can be minimized. A high-resolution current sensor is proposed in low-drop out regulator to sense current for overcurrent limit and overcurrent protection. The measured PCE of proposed system at 15 W are 95.3% and 92.3% for WPC/PMA and A4WP mode, respectively. For MST, power consumption is reduced to 35% courtesy LPTX block.
26 October 2021 in IEEE Access
This paper presents a 0.46 mW and 2.4 GHz; All-Digital Phase-Locked Loop (ADPLL) through an Injection-Locked Frequency Multiplier (ILFM) and Continuous Frequency Tracking Loop (CFTL) circuitry for low power Internet-of-Thing (IoT) applications. In the proposed ADPLL architecture to save power, the need for Time-to-Digital Converter (TDC) is eliminated through providing the CFTL circuitry. This feature makes the design compact, low power, and suitable for IoT applications. The proposed design is based on a synthesizable pulse injection and frequency-locked loop along with an ultra-low-power LC Digitally-Controlled Oscillator (LC-DCO). The presented CFTL circuit adjusts the frequency of the DCO continuously and prevents the frequency drift after the reference injection. Inside the designed LC-DCO core, the power consumption is minimized by optimizing the $\text{g}_{\mathrm {m}}~/\text{I}_{\mathrm {D}}$ and adjusting the power supply to 0.5 V. The proposed ILFM based ADPLL is fabricated in 55 nm CMOS technology and covers the operational frequency range of 2.402 GHz to 2.480 GHz with a reference frequency of 32 MHz. The measured phase noise performance of the ADPLL is −111.15 dBc/Hz at 1 MHz offset frequency from the carrier frequency of 2.4 GHz. It consumes only 0.46 mW power with an active area of 0.129 mm 2 .