Kapil Saha

Mr. Kapil Saha

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2025 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
LCLuca Colombo
Luca Colombo
LSLuca Spagnuolo
Luca Spagnuolo
KSKapil Saha
Kapil Saha
GGGabriel Giribaldi
Gabriel Giribaldi
PSPietro Simeoni
Pietro Simeoni
MRMatteo Rinaldi
Matteo Rinaldi
This letter reports on Solidly-Mounted Bidimensional Mode Resonators (S2MRs) exploiting a highly-optimized Sezawa mode in 30% Scandium-doped Aluminum Nitride (ScAlN) on Silicon Carbide (SiC) and operating near 16 GHz. Experimental results demonstrate mechanical quality factors ( ${Q}_{m}$ ) as high as 380, Bode quality factors ( ${Q}_{\textit {Bode}}$ ) approaching 500, electromechanical coupling coefficients ( ${k}_{t}^{{2}}$ ) of 4.5%, an overall Figure of Merit ( $\textit {FOM} = {Q}_{m} \cdot {k}_{t}^{{2}}$ ) exceeding 17, and power handling greater than 20 dBm for devices closely matched to $50~\Omega $ . To the best of the authors’ knowledge, S2MRs exhibit the highest Key Performance Indicators (KPIs) among solidly mounted resonators in the Ku-band, paving the way for the integration of nanoacoustic devices on fast substrates with high-power electronics, tailored for military and harsh-environment applications.

25 March 2025 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
IAIan Anderson
Ian Anderson
OBOmar Barrera
Omar Barrera
NRNishanth Ravi
Nishanth Ravi
LMLezli Matto
Lezli Matto
KSKapil Saha
Kapil Saha
RLRuochen Lu
Ruochen Lu
This paper reports the first groups of low-loss acoustic solidly mounted resonators (SMR) and acoustic delay lines (ADL) at 14-20 GHz. Bulk acoustic waves (BAW) are confined in thin-film scandium aluminum nitride (ScAlN) on top of dielectric acoustic Bragg reflectors, consisting of alternating silicon dioxide with tantalum pentoxide (Ta2O5/SiO2) or niobium pentoxide (Nb2O5/SiO2) on Si carrier wafers. Stack material parameters are extracted via high-resolution X-ray diffraction (HRXRD) and X-ray reflectivity (XRR). The simulation and experiment show confinement for longitudinal BAW from 14-20 GHz. ADLs show high propagation Q above 478 and 171 for Ta2O5/SiO2 and Nb2O5/SiO2, respectively. SMRs in both stacks perform similarly, showing coupling coefficient (k2) of 2.0%, series Q (Qs) of 156, and parallel Q (Qp) values of 140 for Ta2O5/SiO2, while k2 of 2.4%, Qs of 140, and Qp of 109 for Nb2O5/SiO2, both at 18.6 GHz. Upon development, ScAlN solidly mounted platforms will enable signal processing elements with better power handling.

11 August 2026 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
KSKapil Saha
Kapil Saha
CTChuan Tian
Chuan Tian
KGKarl Grosh
Karl Grosh
SGSiddhartha Ghosh
Siddhartha Ghosh
MRMatteo Rinaldi
Matteo Rinaldi
Scandium-doped aluminum nitride (ScAlN) is a promising replacement for aluminum nitride in MEMS vibration and acoustic sensors due to its higher piezoelectric coefficients and for RF MEMS due to its enhanced piezoelectric response and ferroelectric switching capability. However, poor process conditions often lead to degraded film performance. In this work, we optimized the growth conditions of ScAlN thin films deposited by the reactive pulsed-DC magnetron sputtering system by studying the impact of N2 flow rate, target–substrate distance, substrate temperature, and substrate bias on film stress, crystallinity, and surface morphology. Based on stress measurements, XRD rocking curves along the c-axis (002), and roughness with abnormally oriented grain (AOG) formation probability extracted from AFM and SEM images, an optimized deposition recipe was developed that balances stress, crystallinity, and AOG density. With this optimized recipe, samples were fabricated for dielectric, ferroelectric, and piezoelectric coefficient (d33,f and d31,f) measurements. To verify scalability, d33,f, εr, and tan⁡(δ) were measured on 100, 150, and 200 mm substrates. Dual beam laser interferometry results showed d33,f values of 18 pm/V, εr of 18, and lowest tan⁡(δ) of 0.4%. Cantilever-based d31,f measurements yielded a value of −6.22 pC/N. The optimized ScAlN films also exhibited remanent polarization, Pr = 130 μC/cm2, and coercive field, Ec = 3.5 MV/cm. These results are expected to formulate a basis for future thin film development and applications in MEMS resonators and inertial sensors.

20 January 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
KSKapil Saha
Kapil Saha
CTChuan Tian
Chuan Tian
KGKarl Grosh
Karl Grosh
SGSiddhartha Ghosh
Siddhartha Ghosh
MRMatteo Rinaldi
Matteo Rinaldi
Scandium-doped aluminum nitride (ScAlN) is a promising replacement for undoped aluminum nitride in MEMS vibration and acoustic sensors due to its higher piezoelectric coefficients, and for RF MEMS due to its enhanced piezoelectric response and ferroelectric switching capability. However, poor process conditions often lead to degraded film performance. In this work, we optimized the growth conditions of ScAlN thin films deposited by reactive pulsed-DC magnetron sputtering system by studying the impact of N₂ flow rate, target–substrate distance, substrate temperature, and substrate bias on film stress, crystallinity, and surface morphology. Based on stress measurements, XRD rocking curves along the c-axis (002), and roughness with AOG formation probability extracted from AFM and SEM images, an optimized deposition recipe was developed that balances stress, crystallinity, and AOG density. With this optimized recipe, samples were fabricated for dielectric, ferroelectric, and piezoelectric coefficient (d33,f and d31,f) measurements. To verify scalability, d33,f, εr, and tan(δ) were measured on 100, 150, and 200 mm substrates. Dual beam laser interferometry results showed d33,f values of around 18 pm/V, εr of 18, and lowest tan(δ) of 0.4%. Cantilever-based d31,f measurements yielded a value of −6.22 pC/N. The optimized ScAlN films also exhibited remnant polarization, Pr = 130 μC/cm², and coercive field, Ec = 3.5 MV/cm.