Protected crop production is rapidly expanding in the Mediterranean Basin, and particularly in Morocco. Increased local and overseas demand for these products led to a rapid development in greenhouse usage encouraged by government policies. The aim of this study is to investigate key design parameters that affect the thermal behavior and the heating/cooling energy need of a greenhouse situated in Agadir (Morocco). The parameters include the cladding material characteristics, shape, orientation, and air change rate. The greenhouse is modeled by a developed thermal model using TRNSYS software. The model considers the presence of the plants inside the greenhouse by adding the heat and humidity gain into the heat and water balance of the greenhouse using an evapotranspiration sub-model. The effect of evapotranspiration on the greenhouse thermal behavior was also examined in this study. A validation of the current TRNSYS simulation and evapotranspiration model was made using previous studies from the literature, and the comparison showed fair agreement. The relative error of the annually heating demand obtained by this model is 1.66%, and the evapotranspiration model used in this study shows relative deviation less than 6.5%. The results of this study indicate that the East-West greenhouse orientation is the optimum orientation as it can reduce the annual cost of air-conditioning of the greenhouse by 9.28% compared to North-South orientation. Quonset shape is the optimum greenhouse shape in Morocco as it can save 14.44% of annual cost of air-conditioning instead of the Even-span shape.

In this work, the thermo-hydraulic performance of shell and tube heat exchangers with segmental baffles (STHX) were investigated numerically for different baffle cuts. The heat transfer coefficient and the pressure drop have been considered as key parameters. These two parameters depend on the fluid flow path, which affected by the baffles characteristics (type, spacing, and the baffle cut). Baffles are used to improve heat transfer on the shellside, but they increase the pressure drop, thus requiring a higher pumping power. This Phenomenon reduces the exchanger efficiency. For this purpose, the influence of different baffle cuts in a STHX on the heat transfer coefficient and the pressure drop were studied. The ratio h _s /Δ _p has been taken as a criterion of performance evaluation and the commercial software Ansys-Fluent has been adopted to conduct the simulations. The results show that the heat transfer coefficient and the pressure drop are sensitive to the baffle cut selection. The maximum performance could be obtained with a baffle cut of 25%.

This study is an experimental study on flexural strengthening of reinforced concrete beam where three types of epoxy-bonded jacketing systems are used (glass fiber-reinforced composite (GFRC, S1), jute fiber-reinforced composite (JFRC, S2), and hybrid fiber-reinforced composite (HFRC, S3)) and an unjacketed control beam (S0). All the specimens were subjected to displacement-controlled three-point bending to measure the enhancement of strength, stiffness, and energy absorption using mass-normalized (TPM) and synthetic-content-normalized (TSM) performance indices. Jacketing compared to control also raised the maximum load from 11.80 N to 17.10 N for GFRC (+44.9%), to 14.64 N for JFRC (+24.1%), and to 14.89 N of HFRC (+26.2%). The energy taken up rose from 38.44 J (S0), 152.50 J (S1, +297%), 95.32 J (S2, +148%), and 132.79 J (S3, +245%). Flexural strength was also increased to 56.26 MPa (S1), 43.54 MPa (S2), and 51.38 MPa (S3) and yield strength was raised from 10.43 MPa (S0) to 26.40 MPa (S1), 16.84 Mpa (S2), and 23.05 Mpa (S3). The increase of flexural modulus between S0 (4871.33 MPa) and S1 (12,322.34 MPa), S2 (7862.61 MPa), and S3 (10,759.57 MPa) showed the enhancement of the stiffness. Mass-normalized performance showed great overall efficiency in the case of GFRC and HFRC, with TPM = 3.70 and 3.60 J/kg, respectively, and synthetic-content efficiency was higher in the case of JFRC, with TSM = 9.66 J/kg, which is the advantage of low-synthetic reinforcement in energy-based performance. In general, the suggested jacketing systems have a great influence on flexural responsiveness and power absorption, whereby GFRC and JFRC offer maximum capacity and stiffness, respectively, and the greatest efficiency per unit synthetic material, respectively. In terms of novelty, the paper is one of the first to measure the sustainability-based performance of an epoxy-bonded GFRC, HFRC, and bio-based JFRC jacketing, comparing the results in terms of synthetic-content efficiency (TSM) and mass-normalized indices, which reflect the energy absorption benefits per unit of synthetic material.