Electric ducted fans are gaining prominence in aviation due to their compact size, low noise, and zero emissions compared to conventional gas turbines. This study presents an experimental test system for a 390 mm electric Ducted Propulsion Fan developed by the Aerospace Propulsion Systems group at Hanoi University of Science and Technology. The carbon fiber composite thruster, driven by a centrally located BLDC motor, was mounted on a test stand equipped with force and rotational speed (rpm) sensors. Power was supplied through two battery configurations, eight-pack and nine-pack, with voltage and current monitored and controlled via an ESC module. Experiments conducted from 2000 to 7000 rpm explored the relationship between electrical inputs and aero-propulsive outputs. The results revealed that input power, current, and sound pressure level (SPL) amplified meaningfully with rpm, while the voltage slightly declined. The maximum rpm reached 6500 rpm for the eight-pack and 7000 rpm for the nine-pack configurations. When greater than 6000 rpm, the SPL reaches close to 120 dB. The eight-pack configuration provided higher thrust per volt, whereas the nine-pack offered better thrust per ampere and improved starting power. Although dimensionless indices, including power coefficient (CP), thrust coefficient (CT), and figure of merit (FM), reduced with rpm, the FM remained between 0.7 and 0.75 at medium speeds, demonstrating effective energy conversion.
Autonomous underwater vehicles (AUVs) are widely employed in missions conducted near the seabed, including underwater inspection, seabed mapping, and marine resource exploration. During such operating conditions, the interaction between the AUV and the bottom wall can significantly influence the surrounding flow field and the hydrodynamic characteristics of the vehicle. In this study, a numerical investigation is carried out to examine the influence of near-bottom effects on the hydrodynamic performance of an AUV using a commercial Computational Fluid Dynamics (CFD) solver. The seabed is assumed as a flat wall, and two operating conditions are considered, including an open-water case and a near-bottom case with a clearance ratio of h/LA = 1.93. The flow field is investigated through analyses of hydrodynamic force, pressure distribution, and wake structures. The results indicate that the wall bottom noticeably alters the pressure field and wake development around the AUV, leading to changes in total resistance and flow separation. The findings provide useful insights into the hydrodynamic mechanisms associated with near-bottom operation and offer valuable guidance for the design, control, and operation of AUVs performing missions in shallow or seabed-related missions.
The rapid adoption of electric vehicles, together with increased battery mass and altered load distribution, is placing greater demands on ride comfort and suspension adaptability, while controller optimization may still request forces beyond the instantaneous capability of the physical semi-active actuator if experimentally supported force limits are not explicitly enforced. This study proposes a unified experimentally constrained optimization framework for a magnetorheological damper (MRD)-based semi-active suspension system using a two-degree-of-freedom quarter-car model. The damper is characterized at eleven current levels and represented by a branch-dependent lookup model that provides the zero-current baseline and instantaneous feasible force range. Proportional–integral–derivative (PID) and linear quadratic regulator (LQR) controllers are independently tuned using a genetic algorithm (GA) and particle swarm optimization (PSO) under identical vehicle dynamics, objective functions, tuning excitation, and MRD force constraints. Each candidate force demand is projected onto the experimentally derived feasible range throughout optimization. The controllers are tuned on a composite B–C–D profile and subsequently evaluated over nine road–speed scenarios. PID-PSO reduces the RMS sprung-mass acceleration by 15.91% and achieves the best acceleration performance in six cases, whereas LQR-PSO provides more balanced improvements in body motion, suspension travel, tire response, and force feasibility. The proposed framework therefore provides a more physically constrained basis for the comparative design and evaluation of MRD-based semi-active suspension control.
This study proposes two enhanced configurations for a parallel-channel cold plate in battery thermal management systems to improve thermo-hydraulic performance through the introduction of cylindrical and fin-type baffles. A three-dimensional computational fluid dynamics (CFD) model was developed in ANSYS to simulate fluid flow and heat transfer within the cold plate. A Poly-Hexcore meshing strategy with local refinement and near-wall inflation layers was employed to ensure numerical accuracy while maintaining computational efficiency. A parametric investigation involving 150 cases was conducted to identify the optimal channel configuration. The results indicate that, among the investigated configurations and under the present numerical operating conditions, the fin-type baffle exhibits the most balanced thermo-hydraulic behavior by achieving an effective balance between heat-transfer enhancement and pressure-drop penalty. The present study provides a CFD-based framework for the design and optimization of parallel-channel cold plates for battery thermal management applications.