More and more researchers have been attracted to the research of atmospheric pressure glow discharge (APGD) because of its great prospect in numerous industrial applications. Nevertheless, almost all of the industrial applications are based on achievement of stable, large-volume, and uniform APGD. In a previous study, stable filamentary APGD was obtained by applying a resonant power supply between pin-to-plate electrodes which could limit the peak value of discharge current to supress the glow-to-arc transition through a series-wound resonance principle. The filamentary APGD is centimeter-level in the length but only several millimeters in diameter. Therefore, in order to obtain large-volume and uniform APGD, it is significant to study how to diffuse filamentary APGD in radial direction. With the increasing resonant frequency of alternating current discharge, excited particles (mainly including energetic electrons and trapped ions left from the previous half-cycle discharge) in the electrodes gap increase, which benefits obtaining stable self-sustaining APGD. In this paper, mechanism and law of the influence of resonant frequency on the diffusion of filamentary APGD in ambient air were studied. By comparing the photos of discharge plasma and waveforms of the discharge voltage and current, it is found that the volume of the glow discharge plasma enlarges as the resonant frequency of the power supply increases. It is very significant and anticipating to study how to obtain stable, large-volume, and uniform APGD in ambient air by the resonant power supply.
1 October 2022 in Plasma Sources Science and Technology
This study employs the bursts of high-voltage nanosecond pulses at multi-tens MHz to drive the helium atmospheric pressure plasma jet. Such bursts are obtained by modulating a high-voltage nanosecond pulse based on the wave reflections in a coaxial cable. The development processes and mechanisms of the plasma jet are analyzed in detail based on the discharge waveforms, discharge images, gas temperature, electron density, and axial electric field. Because the time interval between adjacent pulses is much shorter than the characteristic plasma decay time, the discharge channel driven by the first pulse still has high residual electron density and conductivity when the second pulse arrives. The first discharge channel serves as an extension of the high-voltage electrode. In this case, the second discharge starts at the end of the first discharge channel and continues to propagate forward. Driven by the bursts of high-voltage nanosecond pulses, the stepwise propagation of a guided streamer along the plasma jet is observed. The characteristic of the stepwise development of the guided streamer is stable and repeatable under the same condition and does not change at different helium flow rates if the flow is laminar. Reducing the cable length results in a higher equivalent pulse frequency in the bursts and significantly increases the plasma jet length. However, an excessively high frequency will cause a rise in gas temperature and pressure fluctuation in helium flow, resulting in a reduction in the length of the laminar region and an unstable discharge.
Atmospheric pressure glow discharge (APGD) has been widely used in the industrial field. The industrial applications are based on achieving stable and diffusive APGD in a relatively large space. The existing sources only achieved stable and diffusive APGD between a short inter-electrode distance within 5 millimeters. In this paper, the effect of a transverse stationary magnetic field on the diffusion of filamentary APGD was studied in a pin-to-ring coaxial gap. The APGD was driven by a high-voltage resonant power supply, and the stationary magnetic field was supplied by a permanent magnet. The stable and diffusive APGD was achieved in the circular area, which diameter was 20 millimeters. The experimental results revealed that more collision ionization occurred and the plasma was distributed diffusively in the discharge gap by applying the external transverse magnetic field. Besides, it is likely to obtain more stable and diffusive APGD in the coaxial pin-to-ring discharge gap when adjusting the input voltage, transverse magnetic flux density and resonant frequency of the power supply.
In recent years, a lot of research focuses on atmospheric pressure glow discharge, but how to obtain a stable and uniform large-volume glow discharge at atmospheric pressure is still a difficult technological problem, especially in large ambient air gap. In this paper, with an external axial magnetic field applied in the pin-to-plate electrode gap, a stable and diffusive atmospheric pressure glow discharge in ambient air is obtained. Influences of different factors such as the output-voltage amplitude of the power supply, the intensity of the magnetic field, the resonant frequency of power supply, and different inter-electrode gap sizes are studied. The results show that a more diffusive and bigger-volume glow discharge can be obtained by increasing the amplitude of the output voltage of the power supply, the intensity of the external magnetic field, or the resonant frequency in the longer-distance pin-to-plate gap.
The atmospheric pressure glow discharge has a good industrial application prospect, but it is difficult to obtain a stable and diffusive atmospheric pressure glow discharge, especially in the large ambient air gap. In this paper, with a transverse magnetic field applied in the pin-to-ring electrode gap, a stable and diffusive atmospheric pressure glow discharge in ambient air was obtained. The influence of different factors such as the output-voltage amplitude of the power supply, the intensity of the external magnetic field, and the different sizes of ring-cathode were studied from the discharge voltage and current waveforms and the discharge morphology. The results show that a more diffusive and bigger-volume glow discharge can be obtained by increasing the amplitude of the output voltage or the intensity of the external magnetic field, and the more uniform and effective glow discharge can be obtained when choosing the smaller pin-to-ring inter-electrode gap.