Yongting Yang

Ms. Yongting Yang

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 January 2024 in Journal of Laser Applications
Verified
Journal Article
Closed access
PDF file
YYYongting Yang
Yongting Yang
KBKay Bischoff
Kay Bischoff
DMDominik Mücke
Dominik Mücke
CECemal Esen
Cemal Esen
RHRalf Hellmann
Ralf Hellmann
The authors report on ultraviolet ultrashort pulsed laser ablation of fused silica and compare the achievable micromachining results to those obtained by using the fundamental emission wavelength in infrared. Ablation in ultraviolet reveals a stable efficiency for increasing fluences, whereas using an infrared beam exhibits a decreasing trend of the ablation efficiency at higher and increasing fluences. In addition, a significant improvement in the surface quality is found by using an ultraviolet wavelength in a fluence range up to 20 J/cm2 compared to infrared, e.g., revealing an Ra of down to 0.45 μm on using the ultraviolet wavelength compared to Ra = 0.56 μm on using infrared at fluences up 15 J/cm2. Moreover, taking advantage of the high available pulse energy, the authors compare the achievable ablation efficiency and surface roughness using a conventionally focused ultraviolet beam and a defocused ultraviolet beam, finding that the defocused ultraviolet beam possesses a processing quality comparable to that of the focused beam. Finally, the authors exemplify the potential of ultraviolet ultrashort pulsed laser ablation by using a Tesla mixer for microfluidic integration of fused silica.

30 October 2023 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
DFDaniel Franz
Daniel Franz
YYYongting Yang
Yongting Yang
LMLuis Michel
Luis Michel
CECemal Esen
Cemal Esen
RHRalf Hellmann
Ralf Hellmann
We report for the first time on the realization, characterization and application of an ultrashort pulsed laser robot system for flexible and large-area 2D and 3D laser micromachining with 6 articulated axes. To characterize the dynamic positioning of the laser beam during and after axes movement, CMOS image sensors were integrated into the beam path. A method introduced for the alignment of the optical axes allows a reduction of the deviations in laser beam positioning to less than 141.8 ± 92.9 μm within a 110° rotation range of axis 4. In addition, a high laser beam positioning repeatability of less than 102.2 μm is demonstrated over a total period of 14 h for a movement of axis 5 within a range of 0° to 90°. Initial laser cutting, laser structuring and laser marking applications on automotive dashboards and glass substrates are presented for flexible and large area 2D and 3D manufacturing. By applying a special laser cutting strategy for processing AF 32 eco thin glass, high cutting quality is achieved with a taper of up to 96.3% without the generation of cracks, demonstrating the innovative potential of the high-precision laser robot system. Nonetheless, different identified inherent influences of each axis 1–5 during robot axis movement demand for an innovative beam stabilization concept to achieve high precision in laser beam positioning.

12 October 2023 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
YYYongting Yang
Yongting Yang
DFDaniel Franz
Daniel Franz
CECemal Esen
Cemal Esen
RHRalf Hellmann
Ralf Hellmann
We demonstrate an innovative beam stabilization concept consisting of complementary metal-oxide semiconductor cameras and piezo actuators for a six-axis articulated ultrashort pulsed laser robot system. The beam stabilization system is fixed on robot axes 4 and 5. Moving robot axis 5 in an angular range between 0° and 90°, the laser beam position coupled to the actual robot position is monitored by two cameras integrated on robot axis 5 and used for laser beam characterization and model generation. A mathematical description and models generated with machine learning methods, namely, linear regression and neural network, are compared for predicting the beam position drift as a function of robot axis motion, where the neural network model shows a low prediction tolerance of about 7 pixels. In addition, a stand-alone time-triggered beam correction algorithm is developed and implemented on the system, which shows an excellent correction performance for large beam position drifts (below 500 pixels).

27 April 2023 in Journal of Laser Applications
Verified
Journal Article
Open access
PDF file
YYYongting Yang
Yongting Yang
SSSimon Schwarz
Simon Schwarz
CECemal Esen
Cemal Esen
RHRalf Hellmann
Ralf Hellmann
We report on micromilling of fused silica using a 1030 nm femtosecond laser with an intraburst repetition frequency of 40 MHz. Milling of cavities reveals a monotonously increasing ablation efficiency with increasing subpulse number, while the ablation threshold of each subpulse decreases. These results prove that MHz bursts benefit the milling of fused silica. In comparison to the non-burst mode, the maximum efficiency increases about 1.6 times by using a 10 subpulse burst. In addition, bursts cause coarse ablated surfaces, whereas low subpulse numbers in conjunction with increasing fluences lead to a reduction of the surface roughness. A subpulse number of 2 keeps the roughness at the same level as for non-burst at high fluences while enhancing the ablation efficiency about 0.08 mm 3/min/W.

10 April 2025 in Journal of Intelligent Manufacturing
Verified
Journal Article
Open access
PDF file
YYYongting Yang
Yongting Yang
DFDaniel Franz
Daniel Franz
CECemal Esen
Cemal Esen
Ralf HellmannRalf Hellmann
Ralf Hellmann
We report on the evaluation of a beam stabilization system mounted on a six-axis articulated ultrashort pulsed laser robot system for real 3D micromachining. The system integrates a discrete beam guiding system along the robot links and an optical scanner mounted on the final robot axis, enabling high-speed laser scanning for material processing with high power femtosecond pulses. For true 3D micromachining, the robot positions and orients the scanner, allowing scan fields to be stitched or different workpiece areas to be addressed through robot movement. A cascaded beam stabilization system is developed for beam linear and angular position drift correction. This system is implemented on robot links that extend from the robot axis with an integrated ultrashort pulsed laser to the axis with the scanner. The first stage stabilization stabilizes the beam position drift induced by the movement of the axes preceding the laser-integrated axis, as well as the axis equipped with the laser. The second stage is responsible for stabilizing the beam drift resulting from the following axes. A dynamic beam stabilization algorithm including beam position detection and correction with combining the current robot position is introduced and discussed. The stabilization is applied to correct the beam drift after the robot has reached the desired target position for the following scanner movement. In addition, a neural network prediction model is developed and implemented on the system, which reduces the half correction time and increases the beam drift correction efficiency.

25 March 2026 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
DFDaniel Franz
Daniel Franz
YYYongting Yang
Yongting Yang
DMDominik Mücke
Dominik Mücke
CECemal Esen
Cemal Esen
Ralf HellmannRalf Hellmann
Ralf Hellmann
We report for the first time on the realization, comprehensive characterization and application of a 6-axis articulated laser robot using a flexible beam guidance of ultrashort laser pulses via a non-polarization-maintaining hollow-core fiber. Measurements during and after a movement of the fiber-based ultrashort pulsed laser robotic (USPLR) system reveal that fundamental beam characteristics such as transmission, beam pointing and diameter and pulse duration are only marginally affected after passing through the hollow-core fiber. In addition, we studied the application of the USPLR system to laser cutting of brass foils and a printed circuit board (PCB) substrate in a single-path mode and optimize the process with respect to the heat-affected zone and kerf width by varying the applied pulse energy and robot speed. Our findings reveal that heat accumulation plays a significant role for the cutting quality at slow robot speeds of up to 20 mm/s, whereas a reduction of the kerf width down to about 7 µm is feasible. Furthermore, detected vibrations of the USPLR system with varying magnitude at different 3D spatial cutting positions result in oddness of the cutting edges of up to about 200 µm. Nevertheless, optimized process parameters result in a high cutting quality with a small heat-affected zone and a virtually straight and sharp cutting edges in a large processing area of 500 mm $$\times$$ 600 mm $$\times$$ 300 mm, highlighting the substantial potential of the fiber-based USPLR system for flexible and large-area 2D and 3D micromachining.