This paper presents the design and development of a megawatt-scale medium-voltage (MV) hybrid inverter prototype to validate its feasibility and potentials for the electric propulsion on the next-generation electric aircraft system with an onboard MV dc distribution, e.g., 3 kV dc bus in this work. The proposed hybrid converter consists of a three-level active-neutral-point-clamped (ANPC) stage using 3.3 kV silicon IGBTs cascaded with an H-bridge stage using cost-effective 1.2 kV SiC MOSFETs in each phase. Comprehensive design and evaluation of the full-scale prototype are elaborated, including the low-inductance busbar design, converter architecture optimization and system integration. In addition, a low computational cost space vector modulation with common-mode voltage (CMV) reduction feature is proposed to fully exploit the benefits of SiC MOSFET in this hybrid topology. Extensive simulation and experimental results are provided to demonstrate the performance of each power stage and the full converter assembly in both the steady-state operation and variable frequency operations. Compared with the widely adopted IGBT based ANPC converter in MV applications, the proposed 7-L hybrid inverter system features higher power efficiency, reduced harmonics, higher dc voltage utilization, reduced CMV and lower dv/dt, while remains cost effective compared to the solution using MV SiC MOSFETs.
15 June 2020 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The finite-control-set model predictive control (FCSMPC) has been widely studied to control voltage source converters (VSCs) due to its fast-dynamic response and robustness. To design an FCS-MPC for a three-level VSC, it is necessary to design a multi-objective cost function, which usually consists of a term dedicated to control the neutral-point voltage (NP-V) of the VSC dc-link. Nevertheless, selecting weighting factors for the multiple control objectives is time consuming. To address this issue, this paper proposes a new FCS-MPC, which only uses voltage vectors and virtual voltage vectors that do not affect NP-V, such that an inherent dc-link voltage balancing can be achieved. The proposed approach does not only simplify the controller design by using a simplified cost function, which significantly reduce the execution time of the MPC, but also eliminate the voltage and current sensors for the dc-link. Moreover, the proposed MPC can improve the quality of VSC output waveforms. Simulation studies are carried out to verify the superiority of the proposed MPC over the existing ones. The effectiveness of the presented FCS-MPC is also experimentally validated on a T-type converter prototype.
17 April 2023 in IEEE Transactions on Industrial Electronics
Green airborne transportation driven by the state-of-the-art turboelectric propulsion technology has received considerable attention from the aviation industry. To generate electrified thrust, three-level neutral-point-clamped (3L-NPC) converter-fed motor drives are one of the most promising candidates for the powertrain of future aircraft. However, the neutral-point (NP) potential ripple and deviation lead to harmonics and imperil the lifespan of semiconductors and capacitors. Besides, excessive power losses on the converter can limit propulsive power and shorten flight distance. To solve these issues, in this article, a new hybrid modulation strategy is proposed. With respect to the takeoff and climb featuring NP voltage drift-prone regions, carrier-based coordinate-driven modulation waves are exploited to enable virtual-space vectors. For operating points with high power factor, such as cruise, by reconstructing modulated signals, not only can the NP voltage balance be realized but also the switching loss is reduced using active discontinuous pulse trains. The less computational burden is attributed to implementations in the sextant-coordinate system. The effectiveness of the proposed algorithm is verified by simulation results from a Simulink/PLECS model and the experimental results are obtained from a 200 kVA silicon-carbide-based T-type 3L-NPC prototype with a variable output fundamental frequency.
23 March 2022 in IEEE Transactions on Transportation Electrification
The rapid development of more electric aircraft (MEA) raises the demand for high-power converters with significant weight and volume reduction for onboard power distribution. The isolated dc/dc converter using the medium-frequency transformer (MFT) is a feasible solution. To design an MFT with improved electromagnetic and thermal performance, a matrix core transformer (MCT) architecture is proposed with accurate models in this article. With superior heat dissipation ability, the high current windings can be effectively cooled with both natural and forced air convection. In addition, an optimization methodology for MCT design is presented. As a result, the prototype of a 100-kW, 50-kHz MCT with an additive manufactured bobbin is built. The results of both finite element analysis (FEA) simulation and experimental study in a full power dual active bridge (DAB) with the MCT prototype are presented to verify the theoretical design. The power density and efficiency of the MCT reach 17.7 kW/L and 99.63%, respectively.
18 July 2022 in IEEE Transactions on Industry Applications
In this work, an all silicon carbide (SiC) series-resonant converter (SRC) design is proposed and demonstrate to achieve a single stage dc-to-dc conversion from 3kV to 540V (±270V) for future electric aircraft applications. The proposed SRC consists of a neutral-point-clamped (NPC) converter using 3.3kV SiC MOSFETs on the primary side, a H-bridge converter using 900V SiC MOSFET on the secondary side and a high frequency (HF) transformer. The detailed design methods for the SRC power stage and the HF transformer are presented. Especially, a tradeoff between the complexity for the cooling system and the need for high power density and voltage insulation is addressed in the transformer design, leading to a novel multi-layer winding structure design to enhance the insulation capability and also the mechanical robustness. The proposed bobbin design is realized using additive manufacturing. The detailed analysis and modeling of the parasitic capacitance between sections introduced by fringe electrical field is presented. To validate the effectiveness of the proposed SRC design, a 25kW converter prototype using 3.3kV SiC discrete devices has been developed with a peak efficiency of 99.08% achieved in experimental studies.
13 August 2021 in IEEE Open Journal of Power Electronics
This paper proposes a hybrid modulation strategy for a medium-voltage hybrid seven-level (7-L) converter, which consists of a three-phase silicon (Si) IGBT-based active-neutral-point-clamped (ANPC) stage and a cascaded silicon carbide (SiC) MOSFET-based H-bridge (HB) stage in each phase. Within the framework of the proposed modulation strategy, three floating HB converters are controlled using a high-frequency three-level (3-L) space-vector-modulation (SVM), while a low-frequency modulation is applied to the ANPC converter. To regulate the DC voltages across floating capacitors, a zero-sequence voltage (ZSV) injection method is adopted. The proposed method possesses three major advantages. First, it enables the simplification from a 7-L to a 3-L SVM, which significantly reduces the computational burden. Second, with all the high-frequency switching actions assigned to SiC devices in the HB stage, the power loss of the hybrid 7-L converter is reduced. Third, the hybrid modulation together with the ZSV injection enables a wider stable operating range compared to the existing 7-L SVM method. Finally, both simulation and experimental results performed on the scale-down and the full-scale 1 MVA prototype validate the effectiveness of the proposed hybrid modulation strategy.