In this letter, the design of a broadband high-efficiency Doherty power amplifier (DPA) with a bandwidth of 1000 MHz for the 5G frequency band is proposed. The postmatching structure is employed to achieve broadband performance. The proposed DPA shows high efficiency at 6-dB output power back-off (OBO) in the entire 1000-MHz band. The DPA has been designed and implemented using commercial GaN HEMTs to validate the high efficiency and broadband characteristics. The fabricated DPA attains a measured 7.1-11.1-dB saturated gain and a 43.2-44.5-dBm saturated power. The 46%-52% and 58.6%-68.9% drain efficiencies are obtained at 6-dB OBO and saturation throughout the design band, respectively. A 20-MHz LTE modulated signal with a peak-to-average power ratio of 7.2 dB is also applied to the proposed DPA at 3.5 GHz. The average output power is 37.2 dBm. The measured ACPR is improved from -27 to -48.9 dBc with digital predistortion (DPD) performed.
10 January 2020 in IEEE Transactions on Microwave Theory and Techniques
We have demonstrated a frequency multiplier-based multiplying transmitter (MT) architecture, which shows the transmission of wideband modulated signals from the lower frequency band to the millimeter-wave (mm-wave) through the frequency multiplier directly is a viable option. To compensate for the severe nonlinear distortions exhibited by the frequency multiplier in a more efficient way, a two-stage cascaded digital predistortion (DPD) scheme with constrained feedback bandwidth is proposed. The complexity-reduced generalized memory polynomial (GMP) and Nth-order power/root module are used for nonlinear behavioral modeling. Furthermore, the spectral extrapolation and band-divided (BD) modeling methods are employed to achieve more accurate linearization performance of the frequency multiplier over the limited feedback bandwidth. The MT experimental system with an active frequency quadrupler at the Q-band was set up to evaluate the linearization capacity of the proposed BD Nth-order cascaded complexity-reduced GMP (BD-N-CGMP) DPD scheme. In the test for 24-MHz bandwidth 16 quadrature amplitude modulation (QAM) signal, the frequency quadrupler's linearized output at 48.6 GHz with error vector magnitude (EVM) of 1.94% and adjacent channel power ratio (ACPR) of -47.2 dBc could be achieved, even when the feedback bandwidth was limited from 480 to 78 MHz. This demonstrated system significantly decreased the requirement of the digital-to-analog converters (DACs) and analog-to-digital converters (ADCs) sampling rate, and showed promising performances for future MT architecture at mm-wave and subterahertz (sub-THz) frequencies with large signal bandwidth.
26 June 2019 in IEEE Transactions on Microwave Theory and Techniques
Directional modulation (DM) implemented at the transmitter side is a physical layer security technology based on the multi-antenna structure. Current DM methods paid little attention to the issue of the nonlinear distortion of power amplifiers (PAs), which may lead to poor amplifier efficiency and worsen the signal's error vector magnitude (EVM). For the first time, we consider linearization of a DM transmitter using the digital predistortion (DPD) technique. We modify the paralleled DM DPD model to a novel cascaded model based on the characteristics of the DM transmitter. This modified method applies a common DPD to mitigate the nonlinear distortion of all paths and an auxiliary DPD to fine-tune each path, so as to significantly reduce the complexity. In order to validate this idea, two-element uniform linear array (ULA) and four-element ULA experiments were performed, in which 16QAM 20-MHz bandwidth signals with a peak-to-average power ratio (PAPR) of about 8.0 dB were generated for commercial part PAs. Experimental results show that the modified approach has almost the same linearization performance as the paralleled DM DPD technique but reduces the computational complexity significantly.
26 July 2019 in IEEE Transactions on Circuits and Systems II: Express Briefs
Correction of antenna impedance variation in real time with low cost is a challenge. We propose two criteria with the aid of linear fractional transformation (LFT) to fulfill the pre-requirements of binary search scheme. Compared with gradient descent based algorithms, the convergence speed is improved from O(N) to O(logN) at the cost of expensive impedance sensor. To reduce the hardware cost and computational complexity of feedback circuits, the binary search scheme is optimized so that only the detection of the sign of real part and imaginary part of S11 is required. As a result, compared with the impedance sensor, no analog to digital converters (ADCs) and digital calculations are required for the proposed feedback loop. In the end, the proposed scheme is validated with an electromagnetic simulation.
As a crucial step for routing establishment in multi-hop mobile ad hoc networks (MANETs), topology discovery (TD) is extremely challenging when directional antennas are used. In this paper, we propose a joint neighbor discovery and topology exchange (JNDTE) algorithm for the purpose of fast TD. By arranging one topology-information exchange (TIE) closely following the occurrence of one successful neighbor discovery for any pair of nodes, the TD time is significantly decreased due to the avoidance of beam misalignment during the TIE process. Besides, a beam selection strategy is utilized to dynamically adjust the probability distribution for each beam sector to further speed up the TD process. Simulation results show the superiority of the proposed algorithm.
An analytical method to design a power amplifier (PA) with an optimized power added efficiency (PAE) trajectory for envelope tracking (ET) architecture is proposed. To obtain feasible matching solutions for high-efficiency performance of the PA in the dynamic supply operation, hybrid continuous modes (HCM) architecture is introduced. The design space for load impedances of the HCM PAs with nonlinear capacitance is deduced mathematically using the device’s embedding transfer network, without the necessity of using load-pull. The proposed design strategy is verified with the implementation of a GaN PA operating over the frequency range of 1.9 GHz to 2.2 GHz with PAE between 67.8% and 72.4% in the 6.7 dB back-off power region of the ET mode. The ET experimental system was set up to evaluate the application of the PA circuit. Measurement results show that the ET PA at 2.1 GHz reaches the efficiency of 61%, 54%, 44% and an error vector magnitude (EVM) of 0.32%, 0.60%, 0.67% at an average output power of 34.4 dBm, 34.2 dBm, 34.1 dBm for 6.7 dB peak-to-average power ratios (PAPR) signals with 5 MHz, 10 MHz, and 20 MHz bandwidths, respectively. Additionally, tested by a 20 MHz bandwidth 16 quadrature amplitude modulation (QAM) signal, 41.8% to 49.2% efficiency of ET PA is achieved at an average output power of 33.5 dBm to 35.1 dBm from 1.9 GHz to 2.2 GHz.