The electric and optical impulse response of two types of high-speed OLED (HSOLED) driven by ultrashort electrical pulses is investigated. The two HSOLED were designed and manufactured to be characterized in the presence of electrical pulses ranging from 10 to 100 ns in duration and a repetition rate of 10 Hz. The impact of the OLED geometry and the fabrication process on the time response is investigated. This is the first time that an optimized HSOLED exhibits an electrical time response as low as 2.1±0.6 ns and also shorter than the device optical decay time (9.8± 0.2 ns). Moreover, the HSOLED measured current density reaches 3.0 kA/cm 2 , the highest value reported in the literature, with state-of-the-art electroluminescence of 12 W/cm 2 .
We report experimental and theoretical investigations with an in-house fabricated tris(8‐hydroxyquinoline)‐aluminum (Alq3)-based high-speed micro-organic light-emitting diodes (μ-OLEDs) and demonstrate very promising optical pulse responses as short as 400 ps. With a model for an electrically pumped OLED, we simulate the emission of sub-nanosecond optical pulses. The model includes field-dependent (Poole-Frenkel) Langevin recombination and reabsorption of photons by singlets (Stokes-shifted), and by triplets (TA). The good agreement between the measurement and the simulation is the basis for further study of the prospects on the ps time scale, i.e. stimulated emission and conditions for laser operation. For an Alq3-based micro-OLED with high-Q optical cavity, we predict pulsed laser operation with damped relaxation oscillations in the GHz regime and several orders of magnitude linewidth narrowing, but only during 3 ns at most. The simulated current density threshold values vary from 10 kA cm−2 for Q= 500 to less than 1 kA cm−2 for Q = 1000. No continuous-wave (CW) lasing is found due to the accumulation of triplet excitons for t > 5 ns, which has two deteriorating effects, (a) suppression of the gain-providing singlet excitons due to singlet-triplet absorption and (b) suppression of the photon density due to photon absorption by triplets (TA). Prospects for CW-lasing with other organic molecules are discussed.
9 April 2019 in IEEE Transactions on Electron Devices
In this paper, the optical and electrical pulse responses of an optimized high-speed organic light-emitting diode (OLED) is investigated as a function of the pulse duration. The original design is based on the coplanar waveguide electrodes that are implemented on a transparent and conductive oxide thin film. The designed electrodes with reduced serial resistances (13 $\Omega $ ) allow to maximize the pulse energy delivery and to feed the organic device with short electrical pulses of few nanoseconds for the first time. This is achieved by designing the electrodes to have 50- $\Omega $ characteristic impedance, thanks to microwave techniques, and by implementing small values of capacitance (4.5 pF). The experimental results demonstrate $\boldsymbol \mu $ -OLED electrical and optical responses to electrical excitation pulses as short as 2.5 ns, for the first time, and state-of-the-art current densities above 1.7 kA/cm 2 . Moreover, and rather unexpectedly, the developed characterization procedure to extract the reported results demonstrated the first direct measurement of the electroluminescence lifetime of organic materials in the nanosecond time scale.
In the context of the quest for the Organic Laser Diode, we present the multiscale fabrication process optimization of mixed-order distributed-feedback micro-cavities integrated in nanosecond-short electrical pulse-ready organic light-emitting diodes (OLEDs). We combine ultra-short pulsed electrical excitation and laser micro-cavities. This requires the integration of a highly resolved DFB micro-cavity with an OLED stack and with microwave electrodes. In a second challenge, we tune the cavity resonance precisely to the electroluminescence peak of the organic laser gain medium. This requires precise micro-cavity fabrication performed using e-beam lithography to pattern gratings with a precision in the nanometer scale. Optimal DFB micro-cavities are obtained with 300 nm thick hydrogen silsesquioxane negative-tone e-beam resist on 50 nm thin indium tin oxide anode exposed with a charge quantity per area (i.e., dose) of 620 µC/cm2, developed over 40 min in tetramethylammonium hydroxide diluted in water. We show that the integration of the DFB micro-cavity does not hinder the pulsed electrical operability of the device, which exhibits a peak current density as high as 14 kA/cm2.