This paper proposes a new technique to engineer the Fin channel in vertical GaN FinFET toward a straight and smooth channel sidewall. Consequently, the GaN wet etching in the TMAH solution is detailed; we found that the m-GaN plane has lower surface roughness than crystallographic planes with other orientations, including the a-GaN plane. The grooves and slope (Cuboids) at the channel base are also investigated. The agitation does not assist in Cuboid removal or crystallographic planes etching rate enhancement. Finally, the impact of UV light on m and a-GaN crystal plane etching rates in TMAH has been studied with and without UV light. Accordingly, it is found that the m-GaN plane etching rate is enhanced from 0.69 to 1.09 nm/min with UV light; in the case of a-GaN plane etching, UV light enhances the etching rate from 2.94 to 4.69 nm/min.

We investigated a methodology to design light-triggered thyristors thanks to TCAD. The simulation model accuracy, especially the holding current and the minimum incident light intensity to turn-ON, were compared with experimental results. The influence of SiC epitaxial layer lifetime and the incident light properties (wavelength and intensity) on the optically triggered 4H-SiC thyristor characteristics have been studied by simulation. We considered the wavelength dependence of quantum efficiency, penetration depth, and photon energy. The holding current and turn-ON time depends on the lifetime. The minimum intensity to turn-ON the device significantly depends on the wavelength. This intensity becomes less than 0.003 times when the wavelength changed from 380 to 325 nm. In addition, the breakover voltage is affected by the constant incident light even if the intensity is tiny.

Energy harvesting from various ambient energy sources keeps gaining interest to deal with the challenges arising from more and more widespread Internet of Things applications in consumer electronics and industrial applications such as remote sensing. However, available energy is scarce and designers must comply with small size package and thermal dissipation that inevitably lead to compromises. This paper presents a transformer-free and self-powered oscillator that can be directly powered from a very low dc voltage source such as a thermoelectric module and able to deliver dc bias output. Using off-the-shelves parts, such a design is less cumbersome and gives more freedom to designers while tailoring their circuits with respect to their applications. The oscillator consists of a modified Hartley oscillator including a supplementary capacitor that provides a bias voltage in its output. Theoretical analysis is validated through experimental measurements showing that the proposed solution could be deployed in buildings and/or wearable devices as small and cheap complete microgenerators using for example thermoelectric elements or microbial fuel cells.

This paper presents the design, fabrication and characterization results obtained on the last generation (third run) of SiC 10 kV PiN diodes from SuperGrid Institute. In forward bias, the 59 mm² diodes were tested up to 100 A. These devices withstand voltages up to 12 kV on wafer (before dicing, packaging) and show a low forward voltage drop at 80 A. The influence of the temperature from 25 °C to 125 °C has been assessed and shows that resistivity modulation occurs in the whole temperature range. Leakage current at 3 kV increases with temperature, while being three orders of magnitude lower than those of equivalent Si diodes. Double-pulse switching tests reveal the 10 kV SiC PiN diode’s outstanding performance. Turn-on dV/dt and di/dt are −32 V/ns and 311 A/µs, respectively, whereas turn-off dV/dt and di/dt are 474 V/ns and −4.2 A/ns.

The paper investigates the management of drain voltage and current slew rates (i.e., dv/dt and di/dt) of high-speed GaN-based power switches during the transitions. An active gate voltage control (AGVC) is considered for improving the safe operation of a switching cell. In an application of open-loop AGVC, the switching speeds vary significantly with the operating point of the GaN HEMT on either or both current and temperature. A closed-loop AGVC is proposed to operate the switches at a constant speed over different operating points. In order to evaluate the reduction in the electromagnetic disturbances, the common mode currents in the system were compared using the active and a standard gate voltage control (SGVC). The closed-loop analysis carried out in this paper has shown that discrete component-based design can introduce limitations to fully resolve the problem of high switching speeds. To ensure effective control of the switching operations, a response time fewer than 10 ns is required for this uncomplex closed-loop technique despite an increase in switching losses.