Leposava Ristić

Dr. Leposava Ristić

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2019 in Energies
Verified
Journal Article
Open access
PDF file
Jelena LoncarskiJelena Loncarski
Jelena Loncarski
VMVito Giuseppe Monopoli
Vito Giuseppe Monopoli
RLRiccardo Leuzzi
Riccardo Leuzzi
LRLeposava Ristić
Leposava Ristić
FCFrancesco Cupertino
Francesco Cupertino
Wide bandgap (WBG) power devices such as silicon carbide (SiC) can viably supply high speed electrical drives, due to their capability to increase efficiency and reduce the size of the power converters. On the other hand, high frequency operation of the SiC devices emphasizes the effect of parasitics, which generates reflected wave transient overvoltage on motor terminals, reducing the life time and the reliability of electric drives. In this paper, a SiC metal-oxide-semiconductor field-effect transistor (MOSFET) based two level (2L) inverter is systematically studied and compared to the performance of Si insulated-gate bipolar transistor (IGBT) based three level (3L) neutral point clamped (NPC) inverter topologies, for high speed AC motor loads, in terms of efficiency, overvoltages, heat sink design, and cost. A fair comparison was introduced for the first time, having the same output voltage capabilities, output current total harmonic distortion (THD), and overvoltages for the three systems. The analysis indicated the convenience of using the SiC MOSFET based 2L inverter for lower output power. In the case of the maximum output power, the heat sink volume was found to be 20% higher for the 2L SiC based inverter when compared to 3L NPC topologies. Simulations were carried out by realistic dynamic models of power switch modules obtained from the manufacturer’s experimental tests and verified both in the LTspice and PLECS simulation packages.

27 June 2024 in IEEE Access
Verified
Journal Article
Open access
HHHussain Hussain
Hussain Hussain
JLJelena Loncarski
Jelena Loncarski
LRLeposava Ristić
Leposava Ristić
Alberto BelliniAlberto Bellini
Alberto Bellini
The green goals imposed by many countries and the increasing application of renewable energy systems are bringing power electronics to the center of attention. Of particular interest are the wide band-gap devices, as they offer important benefits when considering the efficiency increase and volume reduction. Consequently, they can be viably adopted in renewable energy sources. In this paper, a 2 MW Doubly Fed Induction Generator (DFIG) based Wind Energy Conversion System (WECS) with a bidirectional partial-scale frequency converter composed of two back-to-back converters is considered. The main contribution of the paper is a result of comprehensive comparisons conducted for the two systems: DFIG WECS based on a Si-IGBT converter and DFIG WECS based on a SiC-MOSFET converter in terms of efficiency, volume, and cost. The performed comparison is also a fair comparison, being the selected modules are of the same power ratings. In this way, the previously unspecified but valuable decision-making process regarding the selection of power electronic modules suitable for DFIGs is facilitated. The thermal analysis has been implemented in PLECS, together with the converter control. The realistic libraries obtained from the manufacturers have been included for different power modules. The findings highlight the advantages of employing the Silicon Carbide-based converter in terms of minimizing the size and cost of passive components. They also offer insights on what is needed in order to make the Silicon Carbide solution the absolute best candidate.

16 July 2021 in Energies
Verified
Journal Article
Open access
PDF file
TTTaufik Taluo
Taufik Taluo
LRLeposava Ristić
Leposava Ristić
MJMilutin Jovanovic
Milutin Jovanovic
The Brushless Doubly-Fed Reluctance Generator (BDFRG) is a potential alternative to the Doubly Fed Induction Generator (DFIG) in wind power applications owing to its reasonable cost, competitive performance, and high reliability. In comparison with the Brushless Doubly-Fed Induction Generator (BDFIG), the BDFRG is more efficient and easier to control owing to the cage-less rotor. One of the most preferable advantages of BDFRG over DFIG is the inherently better performance under unbalanced grid conditions. The study conducted in this paper showed that conventional vector control of the BDFRG results in excessive oscillations of the primary active/reactive power, electromagnetic torque, and primary/secondary currents in this case. In order to address such limitations, this paper presented a new control strategy for the unbalanced operation of BDFRG-based wind generation systems. A modified vector control scheme was proposed with the capability to control the positive and the negative sequences of the secondary currents independently, thus greatly reducing the adverse implications of the unbalanced supply. The controller performance has been validated by simulations using a 1.5 MW BDFRG dynamical model built upon the positive and negative sequence equations. The main benefits of the new control strategy are quantified in comparison with conventional PI current control design.

31 May 2021 in Energies
Verified
Journal Article
Open access
PDF file
MMMilovan Majstorovic
Milovan Majstorovic
Marco RiveraMarco Rivera
Marco Rivera
LRLeposava Ristić
Leposava Ristić
Patrick WheelerPatrick Wheeler
Patrick Wheeler
The operation of single-phase Modular Multilevel Converter (MMC) is analyzed in the paper. A mathematical model of the converter is developed and described, based on which the structure and selection of parameters for Classical Control and Optimal Switching State Model Predictive Control (OSS-MPC) are defined. Additionally, the procedure for the determination of circuit parameters, such as submodule capacitance and arm inductance, is described and carried out. The listed control methods are designed and evaluated in Virtual Hardware-in-the-Loop together with single-phase MMC power circuit, regarding three control objectives: AC current control, voltage balancing control and circulating current control. Control methods are evaluated for both steady-state and transient performance and compared based on nine criteria: AC current reference tracking, THD of AC current and voltage, submodule capacitor voltage balancing, total submodule voltage control, circulating current magnitude and THD, number of control parameters and computational complexity. This is the first time that a fair comparison between Classical Control and MPC is considered in literature, resulting in superior performance of both control methods regarding four different criteria and the same performance regarding AC current reference tracking.

23 March 2025 in International Journal of Electrical Power & Energy Systems
Verified
Journal Article
Open access
MMMilovan Majstorovic
Milovan Majstorovic
VNVaibhav Nougain
Vaibhav Nougain
LRLeposava Ristić
Leposava Ristić
ALAleksandra Lekić
Aleksandra Lekić

1 January 2024
Verified
Conference Paper
Closed access
LRLeposava Ristić
Leposava Ristić
The paper investigates the role of advanced use of controlled electrical drives and power lectronics in optimizing energy consumption in industrial processes. These technologies are crucial for enhancing the efficiency, flexibility, and overall performance of industrial processes. The paper emphasizes the principle of minimizing energy losses as the basis of energy efficiency and discusses various strategies for achieving this goal. Variable speed drives (VSDs) are highlighted as essential components for regulating motor speed and torque according to specific application requirements. By adjusting the frequency and voltage supplied to the motor, VSDs ensure that the motor operates at its optimum efficiency point, thereby reducing power losses associated with motors operating at fixed speeds. Furthermore, the integration of power electronics and sophisticated control algorithms enables electrical drives to perform with exceptional precision and responsiveness, as well as to facilitate energy-saving strategies. The paper also discusses how power electronics devices can be employed to improve the power factor of industrial systems, ensuring more effective utilization of electrical power and reducing losses in the distribution network. Additionally, it highlights the role of advanced control systems and power electronics in managing peak loads efficiently, enabling industrial facilities to avoid costly demand charges and optimize energy usage during periods of high electricity prices. Integrating controlled electrical drives and power electronics with smart grid technologies enables demand response, grid interaction, and energy management strategies that contribute to overall energy efficiency and sustainability. The paper systematically analyzes the potential energy savings achievable through functional adjustment of drive components to meet technological requirements. It categorizes savings into two main groups: savings achievable through functional adjustment of drive components and savings at each individual component of the drive system. Selected examples are methodically discussed to illustrate these points.