Epoxy dielectrics with high through-plane thermal conductivity (λ) hold great promise for applications in the thermal management of advanced power electronics. Intensive attempts have been made to improve the λ of epoxy by filling with boron nitride nanosheets (BNNSs). However, it remains a great challenge to achieve a satisfactory increased λ by a small amount of BNNS loading. Herein, we reported a new strategy to prepare epoxy dielectrics with internal three-dimensional phonon transport channels by vacuum freeze-drying and vacuum impregnation. Aramid nanofibers (ANFs) and BNNSs were used for the collaborative construction of a vertical interconnected thermal framework. The resultant ANF-BNNS/epoxy achieved a high through-plane λ of 0.87 W m−1 K−1 at only 1.43 vol. % BNNS, which is ∼17.1% higher than that of the BNNS/epoxy counterpart with even 18.34 vol. % randomly distributed BNNS. The increasing efficiency of λ of epoxy by ANF-BNNS is tenfold more than that of the conventional blending methods. In addition, the ANF-BNNS/epoxy composite also exhibits a low dielectric constant and low dielectric loss. The findings of this study offer an inspired venue to develop high-performance thermally conductive epoxy dielectrics with a minimal BNNS loading.
The development of highly thermally conductive composites with excellent electrical insulation has attracted extensive attention, which is of great significance to solve the increasingly severe heat concentration issue of electronic equipment. Herein, we report a new strategy to prepare boron nitride nanosheets (BNNSs) via an ion-assisted liquid-phase exfoliation method. Then, silver nanoparticle (AgNP) modified BNNS (BNNS@Ag) was obtained by in situ reduction properties. The exfoliation yield of BNNS was approximately 50% via the ion-assisted liquid-phase exfoliation method. Subsequently, aramid nanofiber (ANF)/BNNS@Ag composites were prepared by vacuum filtration. Owing to the “brick-and-mortar” structure formed inside the composite and the adhesion of AgNP, the interfacial thermal resistance was effectively reduced. Therefore, the in-plane thermal conductivity of ANF/BNNS@Ag composites was as high as 11.51 W m−1 K−1, which was 233.27% higher than that of pure ANF (3.45 W m−1 K−1). The addition of BNNS@Ag maintained tensile properties (tensile strength of 129.14 MPa). Moreover, the ANF/BNNS@Ag films also had good dielectric properties and the dielectric constant was below 2.5 (103 Hz). Hence, the ANF/BNNS@Ag composite shows excellent thermal management performance, and the electrical insulation and mechanical properties of the matrix are retained, indicating its potential application prospects in high pressure and high temperature application environments.
30 August 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
The surface discharge along the valve side bushing could directly result in single-pole or even bipolar shutdown of the UHVDC project, leading to a significant power grid operation accident. The AC-DC combined voltage and intense vertical component electric field exert a significant influence on the design of the external insulation of the valve side bushing. The paper presented measurements of the stable propagation fields, velocities, and luminous intensity of the streamer discharge in a three-electrode device subjected to combined AC-DC voltage and an intense vertical component electric field directed away from the insulation surface. The propagation of the streamer discharge was inhibited by the intense vertical component electric field directed away from the insulation surface, increased stable propagation field and reduced propagation velocity. The length of the embedded electrode specifically influenced the magnitude of the vertical component electric field along the dielectric surface, thereby significantly impacting the progression of streamer discharge. The influence mechanism of the electric field distribution and ionization effect was investigated to explore the characteristics of streamer discharge under intense vertical component electric fields directed away from the insulation surface. The sliding flashover discharge mechanism along the valve side bushing belonging to the UHVDC converter transformer was elucidated and explicated from the streamer discharge perspective.
18 April 2022 in IEEE Transactions on Power Electronics
Direct current (dc) voltage sensor in each cell of the cascaded H-bridge rectifier (CHBR) is traditionally indispensable for capacitor voltage balancing control. The cost of dc sensors will increase with the number of cells. This letter proposes a strategy for dc-voltage digital sampling based on sliding window recursive least square (RLS), which employs only one voltage sensor. Sliding window RLS is used to decouple voltage information within one sampling interval. For the actual situation where the modulation waves of cells are different, this method owns faster updating rate and higher detection precision compared to the existing multisampling method. A downscale test platform of the single-phase CHBR is built to verify the correctness and effectiveness of the proposed method. The result shows that better current quality and steadier dc voltage are achieved.
This study investigated the influencing mechanisms of shed shape on direct-current pollution flashover voltage and pressure decrease exponent through artificial pollution tests on a glass experimental model in Beijing (50 m altitude) and Tibet (4300 m altitude). Arc development prior to the flashover was quantitatively recorded using a high-speed camera, and three arc development modes along the pollution surface or in the inter-shed space were then extracted through arc development analysis. The occurrence probabilities of the three arc modes under various shed overhangs, altitudes, and shed spacings were analyzed. Mode probability was used to interpret the decreasing flashover voltage gradient with increasing shed overhang and decreasing shed spacing. Research indicates that pressure decrease exponent rises with shed overhang increase, as explained from the perspective of arc development probability. The quantitative relation between leakage distance efficiency and pressure decrease exponent was theoretically derived and its validity was proven through comparing the calculated with the measured.
By 2025, China successfully commissioned more than 40 Ultra-High Voltage (UHV) power transmission and transformation projects, establishing the world’s largest and most technologically advanced UHV grid