YASSER DIAB

Dr. YASSER DIAB

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
MCMatthieu Cordier
Matthieu Cordier
YDYASSER DIAB
YASSER DIAB
JCJérôme Cavoret
Jérôme Cavoret
FMFida Majdoub
Fida Majdoub
CCChristophe Changenet
Christophe Changenet
Fabrice VILLEFabrice VILLE
Fabrice VILLE
Optimising the friction coefficient helps reduce friction losses and improve the efficiency of mechanical systems. The purpose of this study is to experimentally investigate the impact of roughness orientation on the friction coefficient in elastohydrodynamic (EHD) contact. Tests were carried out on a twin-disc machine. Three pairs of discs of identical material (nitrided steel) and geometry were tested: a smooth pair (the root mean square surface roughness Sq = 0.07 µm), a pair with transverse roughness and another with longitudinal roughness. The two rough pairs have similar roughness amplitudes (Sq = 0.5 µm). A comparison of the friction generated by these different pairs was carried out to highlight the effect of the roughness orientation under different operating conditions (oil injection temperature from 60 to 80 °C, Hertzian pressure from 1.2 to 1.5 GPa and mean rolling speed from 5 to 30 m/s). Throughout all the tests conducted in this study, longitudinal roughness resulted in higher friction than transverse, with an increase of up to 30%. Moreover, longitudinal roughness is more sensitive to variations in operating conditions. Finally, in all tests, the asperities of longitudinal roughness were found to influence the friction behaviour, unlike transverse roughness.

1 September 2026 in Surfaces
Verified
Journal Article
Open access
PDF file
Maxence BigerelleMaxence Bigerelle
Maxence Bigerelle
JLJulie Lemesle
Julie Lemesle
Eddy ChevallierEddy Chevallier
Eddy Chevallier
YDYASSER DIAB
YASSER DIAB
TTThomas Touret
Thomas Touret
Fabrice VILLEFabrice VILLE
Fabrice VILLE
This study investigates the correlations between the parameters of the Hysteresis-Attrition-Friction model (HAF), hysteresis (h), attrition (a), and friction coefficient (ν), under different surface conditions and contact pressures. The HAF model, a sigmoidal model developed in-house, provides a novel approach for characterizing tribological behaviour through its three key parameters (h, a, ν). The analysis employed a bootstrapping method to generate numerous parameter samples, allowing for the estimation of joint distributions and the identification of correlations between parameter pairs. The model here is applied to data from experiments conducted using both smooth and rough surface configurations at three distinct contact pressures: 1.2 GPa, 1.6 GPa, and 1.9 GPa. The results revealed a positive correlation between hysteresis and attrition across both surface types, indicating that higher energy dissipation through hysteresis is associated with increased friction. Conversely, negative correlations were found between hysteresis and friction coefficient, and between attrition and friction, suggesting a trade-off between energy dissipation and friction. The bivariate kernel density plots further highlighted these patterns, helping to visualize the complex relationships within the model. The results emphasize the importance of considering surface conditions and pressure when applying the HAF model to predict performance in tribological systems.

14 August 2025 in Dynamics
Verified
Journal Article
Open access
PDF file
TTThibaut Torres
Thibaut Torres
YDYASSER DIAB
YASSER DIAB
CCChristophe Changenet
Christophe Changenet
TTThomas Touret
Thomas Touret
BGBerengere Guilbert
Berengere Guilbert
This study aims to develop a new model for windage losses, building upon existing formulation, complemented by dedicated experimental campaigns and a specific methodology designed to isolate and quantify windage losses. The model relies on an analytical approach to flow characterization, incorporating a correction factor accounting for air density reduction. The experimental investigation was carried out on a dedicated test bench and includes both spur and helical gears. The results demonstrate good agreement between the proposed model and the experimental data, with and without the presence of nearby obstacles, such as side flanges, highlighting the model’s robustness across different configurations. The proposed windage loss model reproduces the experimental results with significantly greater accuracy than the original one, yielding relative deviations below 5% compared to almost 20% for spur gears, and below 9% compared to over 21%, and in some cases up to 50%, for helical gears.

8 October 2025 in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Verified
Journal Article
Closed access
JWJeroen Wensing
Jeroen Wensing
YDYASSER DIAB
YASSER DIAB
JCJerome Cavoret
Jerome Cavoret
Fabrice VILLEFabrice VILLE
Fabrice VILLE
BWBenny Wemekamp
Benny Wemekamp
Hybrid ball bearings with rolling elements made of silicon nitride show important friction, temperature, and power loss benefits compared to full steel bearings under mixed lubrication. This is of particular interest for electrical vehicle (EV) range extension in the automotive industry, where hybrid bearings are used in the electric motor with integrated gearbox to avoid electrical erosion damage. Same benefits can be obtained for industrial electric motors with high frequency variable speed drives where the hybrid bearing acts as an insulator against electrical currents. In this study bearing temperatures and system torque are measured in a modified FZG gearbox for both hybrid and steel ball bearings. The gear set was designed with a small helix angle to create an axial preload to the sets of 6306 deep groove ball bearings with C3 clearance. To reach mixed lubrication conditions, a small amount of low viscous oil was used operating at high temperatures up to a maximum of 100°C. Results in this study show that for mixed lubrication the hybrid bearings run 2-4°C cooler compared to steel ones, while the temperature gradient is similar. Due to lower friction in the hybrid bearings, the FZG test box efficiency is on average improved with 3%.

15 September 2026 in Technologies
Verified
Journal Article
Open access
PDF file
Maxence BigerelleMaxence Bigerelle
Maxence Bigerelle
JLJulie Lemesle
Julie Lemesle
Eddy ChevallierEddy Chevallier
Eddy Chevallier
YDYASSER DIAB
YASSER DIAB
TTThomas Touret
Thomas Touret
Fabrice VILLEFabrice VILLE
Fabrice VILLE
Accurate modeling of the tooth friction coefficient is central to analyses of efficiency, vibration, and durability in enclosed gear drives. Physics-based models describe these contacts using a large set of coupled thermal, contact, and lubrication laws whose individual parameters have uncertainties that are difficult to propagate. This study proposes a compact alternative: the HAF model, a three-parameter phenomenological description of the friction coefficient as a function of the slide-to-roll ratio (SRR). The three parameters have distinct tribological interpretations: h (hysteresis) governs the steepness of the sigmoidal transition, a (attrition) governs the slope of the plateau, and ν (friction level) governs the overall magnitude. The model is calibrated using nonlinear regression with fourteen two-disc traction curves acquired with a one-factor-at-a-time (star) design around a reference operating point (1.6 GPa, 80 °C, and 20 m/s): the contact pressure (1.2, 1.6, and 1.9 GPa), the injection temperature (40, 80, and 100 °C), and the mean speed (10, 20, and 30 m/s) are each varied in turn, for both smooth and rough discs. Parameter uncertainty is quantified using the residual-resampling bootstrap (BIG) established in a companion paper and applied over 105 iterations; it yields near-Gaussian, weakly correlated parameter distributions. The three HAF parameters are then expressed as linear functions of load, temperature, speed, and roughness; least-squares inference across the fourteen conditions shows that eleven of the fifteen regression coefficients differ significantly from zero at the 5% level, with roughness having the strongest effect on the friction level (t = 7.98). Substituting these laws into the HAF equation and reoptimizing the resulting expression globally yields a single closed-form model that reproduces the measured friction coefficient with a residual spread of σ ≈ 0.001 in friction-coefficient units (R2 ≈ 0.996) and approximately Gaussian, zero-mean, and homoscedastic residuals with no evident systematic structure. Being differentiable and equipped with bootstrap confidence intervals, the model predicts friction throughout the tested operating envelope—across which the maximum friction coefficient varies by a factor of eight, from 0.0049 to 0.0388—and supports gradient-based optimization of low-friction operating conditions. The contribution of this study is a compact, interpretable, and statistically characterized predictive law for tooth friction, expressed in closed form as a function of the operating conditions and of the surface state.