Emanuele Tognoli

Dr. Emanuele Tognoli

Department of Engineering “Enzo Ferrari”, University of Modena and Reggio Emilia, Modena, Emilia-Romagna, Italy
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 August 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
EBElena Bassoli
Elena Bassoli
SDSilvio Defanti
Silvio Defanti
ETEmanuele Tognoli
Emanuele Tognoli
NVNicolò Vincenzi
Nicolò Vincenzi
LELorenzo Degli Esposti
Lorenzo Degli Esposti
High cost, unpredictable defects and out-of-tolerance rejections in final parts are preventing the complete deployment of Laser-based Powder Bed Fusion (LPBF) on an industrial scale. Repeatability, speed and right-first-time manufacturing require synergistic design approaches. In addition, post-build finishing operations of LPBF parts are the object of increasing attention to avoid the risk of bottlenecks in the machining step. An aluminum component for automotive application was redesigned through topology optimization and Design for Additive Manufacturing. Simulation of the build process allowed to choose the orientation and the support location for potential lowest deformation and residual stresses. Design for Finishing was adopted in order to facilitate the machining operations after additive construction. The optical dimensional check proved a good correspondence with the tolerances predicted by process simulation and confirmed part acceptability. A cost and time comparison versus CNC alone attested to the convenience of LPBF unless single parts had to be produced.

11 August 2018 in Metals
Verified
Journal Article
Open access
PDF file
Elena BassoliElena Bassoli
Elena Bassoli
LDLucia Denti
Lucia Denti
ACAndrea Comin
Andrea Comin
Antonella SolaAntonella Sola
Antonella Sola
ETEmanuele Tognoli
Emanuele Tognoli
Laser-based powder bed fusion (L-PBF) is nowadays the preeminent additive manufacturing (AM) technique to produce metal parts. Nonetheless, relatively few metal powders are currently available for industrial L-PBF, especially if aluminum-based feedstocks are involved. In order to fill the existing gap, A357.0 (also known as A357 or A13570) powders are here processed by L-PBF and, for the first time, the fatigue behavior is investigated in the as-built state to verify the net-shaping potentiality of AM. Both the low-cycle and high-cycle fatigue areas are analyzed to draw the complete Wohler diagram. The infinite lifetime limit is set to 2 × 106 stress cycles and the staircase method is applied to calculate a mean fatigue strength of 60 MPa. This value is slightly lower but still comparable to the published data for AlSi10Mg parts manufactured by L-PBF, even if the A357.0 samples considered here have not received any post-processing treatment.

1 February 2022 in Additive Manufacturing
Verified
Journal Article
Closed access
MGManuela Galati
Manuela Galati
SDSilvio Defanti
Silvio Defanti
ASAbdollah Saboori
Abdollah Saboori
GRGiovanni Rizza
Giovanni Rizza
ETEmanuele Tognoli
Emanuele Tognoli
LILuca Iuliano
Luca Iuliano

24 June 2023 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Open access
Maria Laura GattoMaria Laura Gatto
Maria Laura Gatto
GCGiorgia Cerqueni
Giorgia Cerqueni
RGRiccardo Groppo
Riccardo Groppo
ESEleonora Santecchia
Eleonora Santecchia
ETEmanuele Tognoli
Emanuele Tognoli
Paolo MengucciPaolo Mengucci
Paolo Mengucci
Graded lattice scaffolds based on rhombic dodecahedral (RD) elementary unit cell geometry were manufactured in 316L stainless steel (SS) by laser powder bed fusion (LPBF). Two different strategies based on varying strut thickness layer-by-layer in the building direction were adopted to obtain the graded scaffolds: a) decreasing strut size from core to edge to produce the dense-in (DI) structure and b) increasing strut size in the same direction to produce the dense-out (DO) structure. Both graded structures (DI and DO) were constructed with specular symmetry with respect to the central horizontal axis. Structural, mechanical, and biological characterizations were carried out to evaluate feasibility of designing appropriate biomechanical performances of graded scaffolds in the perspective of bone tissue regeneration. Results showed that mechanical behavior is governed by graded geometry, while printing parameters influence structural properties of the material such as density, textures, and crystallographic phases. The predominant failure mechanism in graded structures initiates in correspondence of thinner struts, due to high stress concentrations on strut junctions. Biological tests evidenced better proliferation of cells in the DO graded scaffold, which in turn exhibits mechanical properties close to cortical bone. The combined control of grading strategy, printing parameters and elementary unit cell geometry can enable implementing scaffolds with improved biomechanical performances for bone tissue regeneration.

18 March 2019 in Advanced Engineering Materials
Verified
Journal Article
Closed access
PDF file
AGAndrea Gatto
Andrea Gatto
EBElena Bassoli
Elena Bassoli
LDLucia Denti
Lucia Denti
Antonella SolaAntonella Sola
Antonella Sola
ETEmanuele Tognoli
Emanuele Tognoli
JOJose Luis Ocaña
Jose Luis Ocaña

Verified
Journal Article
Open access
PDF file
SDSilvio Defanti
Silvio Defanti
CCCamilla Cappelletti
Camilla Cappelletti
Andrea GattoAndrea Gatto
Andrea Gatto
ETEmanuele Tognoli
Emanuele Tognoli
FFFabrizio Fabbri
Fabrizio Fabbri
The Laser Powder Bed Fusion (L-PBF) process is recognized for high-end industrial applications due to its ability to produce parts with high geometric complexity. If lightweighting is one of the main strengths of L-PBF, a weakness is still the trade-off between high mechanical properties and competitive productivity. This objective can be targeted through a fine tuning of the process parameters within the manufacturing window. The paper pursues the combined optimization of part quality and process productivity for AlSi10Mg by going beyond the commonly used approach based solely on volumetric energy density. The effects of hatch distance and scan speed on the two targets were analyzed in detail. The best results were achieved by the adoption of a high scan speed and a low hatch distance, with notably different outcomes for nearly the same energy density.