Nowadays, the use of the hardware in the loop (HIL) simulation has gained popularity among researchers all over the world. One of its main applications is the simulation of power electronics converters. However, the equipment designed for this purpose is difficult to acquire for some universities or research centers, so ad-hoc solutions for the implementation of HIL simulation in low-cost hardware for power electronics converters is a novel research topic. However, the information regarding implementation is written at a high technical level and in a specific language that is not easy for non-expert users to understand. In this paper, a systematic methodology using LabVIEW software (LabVIEW 2018) for HIL simulation is shown. A fast and easy implementation of power converter topologies is obtained by means of the differential equations that define each state of the power converter. Five simple steps are considered: designing the converter, modeling the converter, solving the model using a numerical method, programming an off-line simulation of the model using fixed-point representation, and implementing the solution of the model in a Field-Programmable Gate Array (FPGA). This methodology is intended for people with no experience in the use of languages as Very High-Speed Integrated Circuit Hardware Description Language (VHDL) for Real-Time Simulation (RTS) and HIL simulation. In order to prove the methodology’s effectiveness and easiness, two converters were simulated—a buck converter and a three-phase Voltage Source Inverter (VSI)—and compared with the simulation of commercial software (PSIM^® v9.0) and a real power converter.

Nowadays, reducing energy consumption is the fastest way to reduce the use of fossil fuels and, therefore, greenhouse gas emissions. Heating, Ventilation, and Air Conditioning (HVAC) systems are used to maintain an indoor environment in comfortable conditions for its occupants. The combination of these two factors, energy efficiency and comfort, is a considerable challenge for building operations. This paper introduces a design approach to control an HVAC, focused on an energy consumption reduction in the operation of the HVAC system of a building. The architecture was developed using a Raspberry Pi as a coordinator node and wireless connection with sensor nodes for environmental variables and electrical measurement nodes. The data received by the coordinator node is sent to the cloud for storage and further processing. The control system manages the setpoint of the HVAC equipment, as well as the turning on and off the HVAC compressor using an XBee-based solid state relay. The HVAC temperature control system is based on the Predicted Mean Vote (PMV) index calculation, which is used by the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) to find the appropriate setpoint to meet the thermal comfort of 80% of users. This method combines the values of humidity and temperature to define comfort zones. The coordinator node makes the compressor control decisions depending on the value obtained in the PMV index. The proposed PMV-based temperature control system for the HVAC equipment achieves energy savings ranging from 33% to 44% against the built-in control of the HVAC equipment, when operating with the same setpoint of 26.5 grades centigrade.

High boost converters, because of its ability of having high gain level, have become important in applications for energy generation known as renewable sources. High efficiency, few components and low voltage and current stress on switches are desired features in these kinds of converters. Double tapped boost converter with just a single switch is proposed in this study for high gain; two pairs of coupled magnetically coils are charged in parallel and discharged in series with the source, this let us to obtain not only a higher gain with very few components but also an acceptable efficiency. Not only analysis for the topology is shown, but also simulation and experimental results are presented in order to illustrate the system behaviour for an output power of 200 W. The system efficiency is closer to 90% at hard switching.

Although PV systems are one of the most widely used alternatives as a renewable energy source due to their well-known advantages, there are significant challenges to address related to voltage fluctuations and reverse power flow caused by high PV penetration scenarios. As a potential solution to this problem, an active power management strategy is proposed in this work using a residential cluster as a benchmark. The proposed strategy is analyzed and experimentally verified, offering a simple way to reduce the voltage fluctuations by regulating the active power delivered by the PV system, achieving also relevant functionalities for the system, such as the regulation of the DC bus voltage, maximum power point tracking (MPPT), synchronization with the grid voltage, detection of high penetration conditions, and a simple strategy for the main controller with an effective performance. The proposal system shows satisfactory results being able to maintain grid voltage fluctuations within the voltage standard specifications.