Oxy-fuel coal combustion, together with carbon capture and storage or utilization, is a set of technologies allowing to burn coal without emitting globe warming CO2. As it is expected that oxy-fuel combustion may be used for a retrofit of existing boilers, development of a novel oxy-burners is very important step. It is expected that these burners will be able to sustain stable flame in oxy-fuel conditions, but also, for start-up and emergency reasons, in conventional, air conditions. The most cost effective way of achieving dual-mode boilers is to introduce dual-mode burners. Numerical simulations allow investigation of new designs and technologies at a relatively low cost, but for the results to be trustworthy they need to be validated. This paper proposes a workflow for design, modeling, and validation of dual-mode burners by combining experimental investigation and numerical simulations. Experiments are performed with semi-industrial scale burners in 0.5 MWt test facility for flame investigation. Novel CFD model based on ANSYS FLUENT solver, with special consideration of coal combustion process, especially regarding devolatilization, ignition, gaseous and surface reactions, NOx formation, and radiation was suggested. The main model feature is its ability to simulate pulverized coal combustion under different combusting atmospheres, and thus is suitable for both air and oxy-fuel combustion simulations. Using the proposed methodology two designs of pulverized coal burners have been investigated both experimentally and numerically giving consistent results. The improved burner design proved to be a more flexible device, achieving stable ignition and combustion during both combustion regimes: conventional in air and oxy-fuel in a mixture of O2 and CO2 (representing dry recycled flue gas with high CO2 content). The proposed framework is expected to be of use for further improvement of multi-mode pulverized fuel swirl burners but can be also used for independent designs evaluation.
The article presents a method of controlling the size of droplets generated by a system that sprays a high-viscosity liquid containing particles of a solid body, i.e., a catalyst. The work is a continuation of previous research concerning the spraying of liquids with a catalyst, which improves the efficiency of the process. As a result of the conducted CFD calculations, it was found that to bring the catalyst to the system, a droplet with a diameter of at least 30 µm should be generated. The tests were carried out on a laboratory scale on a model isopropanol-water system. A polymer containing Raney nickel particles was added to the suspension. The analysis of the obtained data confirmed the possibility of generating droplets with the desired diameters in order for the liquid carrying the catalyst to not evaporate before it is delivered to the combustion chamber. The designed and constructed test system allows the diameters of the generated droplets to be controlled by changing the settings of the spraying nozzle. Moreover, it enables the parameters of the process, and the spraying itself, to be controlled. In further work, tests on a real 0.5 MW facility are planned. Due to the use of a catalyst, a greater degree of fuel burnout can be obtained, and the dynamics of the combustion process can be improved. Additionally, the parameters of the emitted exhaust gases and ash composition can also be enhanced.
The paper provides an outlook on future directions of research and the possible applications for pulverized coal-fired boilers. One potential direction for future research is to focus on the ways to improve the efficiency of pulverized coal-fired boilers. This could involve developing new combustion technologies that are able to more thoroughly burn the coal and produce less waste or finding ways to capture and use the excess heat that is generated during the combustion process. The pulverized coal combustion process in power boilers is still being improved by the preliminary cleaning of coal and the use of various catalytic additives. Another area of research that could be valuable is the development of advanced control systems and monitoring technologies for pulverized coal-fired boilers. These systems could be used to optimize the performance of the boiler and ensure that it is operating at maximum efficiency while also providing real-time data on the condition of the boiler and any potential problems that may arise. The analysis of literature shows that several future paths of development and scientific research related to the technology of pulverized coal combustion in boilers can be distinguished.
Conventional coal-fired burners are designed to operate within specific limits that, in part, result from the need to efficiently burn the fuel. These designs have been developed to ensure stable combustion, lower NOx emissions and increase the combustion efficiency through techniques such as air staging and adding swirl to the combustion air. Recent requirements to reduce CO2 emissions from coal-fired boiler plant has focussed on the co-firing of biomass, primarily wood, either by delivering the pulverised biomass with the coal or through separate burners. To date this approach has typically taken place at substitution levels of around 5% by mass and at these levels the operation of the burners and boiler is not adversely affected. However, as the proportion of biomass increases the fuel characteristics of the blend moves further away from the burner design parameters. This can lead to combustion instabilities and in extreme cases extinction of the flame. In order to co-fire higher concentrations of biomass a system or technique is required that can detect the onset of these instabilities and warn before the combustion conditions become dangerous. In this paper a novel technique based around the Wigner-Ville transform is presented that shows promise at being able to temporarily resolve the conditions that could result in the onset of burner instabilities for three cases; the first will present results from the combustion of 100% bituminous coal, whilst the second and third cases will present the results from experiments where the proportion of biomass was set at 10% and 20% by mass with the same bituminous coal. In each experiment the secondary combustion air was first reduced from a nominal stable condition and then subsequently increased from the same stable condition. It was found that the Wigner transform was able to resolve flicker frequency changes as the airflow rate was reduced. These changes were subsequently used in a neural network to automatically detect drastic changes in the air flow rates to the burner and could provide a means by which utility operators could detect dangerous flame instability conditions in real-time.
1 June 2016 in Journal of Thermal Science and Engineering Applications