Sara Sendino

Mrs. Sara Sendino

Aerospace Advance Manufacturing Research Center - CFAA
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2023 in Mechanical Systems and Signal Processing
Verified
Journal Article
Open access
IAIñigo Aldekoa
Iñigo Aldekoa
AOAnder Del Olmo
Ander Del Olmo
LPLeonardo Sastoque Pinilla
Leonardo Sastoque Pinilla
SSSara Sendino
Sara Sendino
Unai López NovoaUnai López Novoa
Unai López Novoa
Luis Norberto López De LacalleLuis Norberto López De Lacalle
Luis Norberto López De Lacalle

24 October 2020 in Coatings
Verified
Journal Article
Open access
PDF file
SSSara Sendino
Sara Sendino
MGMarc Gardon
Marc Gardon
Fernando LartateguiFernando Lartategui
Fernando Lartategui
SMSilvia Martinez
Silvia Martinez
Aitzol LamíkizAitzol Lamíkiz
Aitzol Lamíkiz
The manufacture of multiple parts on the same platform is a common procedure in the Laser Powder Bed Fusion (L-PBF) process. The main advantage is that the entire working volume of the machine is used and a greater number of parts are obtained, thus reducing inert gas volume, raw powder consumption, and manufacturing time. However, one of the main disadvantages of this method is the possible differences in quality and surface finish of the different parts manufactured on the same platform depending on their orientation and location, even if they are manufactured with the same process parameters and raw powder material. Throughout this study, these surface quality differences were studied, focusing on the variation of the surface roughness with the angle of incidence of the laser with respect to the platform. First, a characterization test was carried out to understand the behavior of the laser in the different areas of the platform. Then, the surface roughness, microstructure, and minimum thickness of vertical walls were analyzed in the different areas of the platform. These results were related to the angle of incidence of the laser. As it was observed, the laser is completely perpendicular only in the center of the platform, whilst at the border of the platform, due to the incidence angle, it melts an elliptical area, which affects the roughness and thickness of the manufactured part. The roughness increases from values of Sa = 5.489 μm in the central part of the platform to 27.473 μm at the outer borders while the thickness of the manufactured thin walls increases around 40 μm.

25 November 2022 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
SSSara Sendino
Sara Sendino
SMSilvia Martinez
Silvia Martinez
Fernando LartateguiFernando Lartategui
Fernando Lartategui
MGMarc Gardon
Marc Gardon
Aitzol LamíkizAitzol Lamíkiz
Aitzol Lamíkiz
JGJavier Jesus Gonzalez
Javier Jesus Gonzalez
One of the key aspects of the laser powder bed fusion (L-PBF) process is the quality of the raw powder since it affects the final properties of the manufactured parts. In this study, 13 batches of Inconel® 718 powder were analysed, all of them being specially designed for L-PBF technology and meeting similar requirements but coming from different suppliers. Therefore, these batches have certain differences in their characteristics, including the particle size distribution (PSD). This study presents the relationship between the PSD of each batch and the surface roughness obtained in the manufactured parts. For the roughness study, Sa and Sz parameters are presented; in addition, the size and frequency of the particles adhered to the surface were quantified, and an autocorrelation analysis was carried out. Furthermore, after this analysis, the parts were sandblasted in order to repeat the same analysis after removing the adhered particles from the surface. This work points to the fact that the particles adhered to the surface are the smallest particles in the powder batch, and their size affects the roughness of the final part. This means that the surface roughness is strongly related to the fraction of smaller particles within the PSD of the batch, while there is no relationship between the surface roughness and the larger particles.