Complex surfaces such as helical ones are commonly used in machinery. Such surfaces can be obtained by various machining processes, one of these processes being thread whirling. The influence of machining conditions needs to be better understood to develop a more precise prediction of the specific resulting errors involved in thread whirling. This paper firstly presents the theoretical conditions which generate micro-deviations on whirled surfaces. A theoretical model which considers the geometrical parameters describing the whirling head and cutters and the process’s whole kinematics was developed. The threaded surface was described as a complex compound surface resulting from intersecting successive ruled helical surfaces corresponding to the cutting edges of the set of cutters from the whirling head. Numerical simulation results were exemplified and validation experiments were both designed and performed. Empirical mathematical models were established to highlight the influence of the input factors such as thread pitch and external diameter, the ratio between the diameter of cutters’ top edge disposal and the thread’s external diameter, the rotary speed of the whirling head, and the rotary speed of the workpiece on some accuracy elements and roughness parameters of the threaded surface.
Cam mechanisms, covering a large structural variety, are widely used in machinery, mainly as components of automated systems. Their functioning behavior is affected by negative dynamic phenomena determined by specific high velocities and acceleration rates. Within the various types of research on the dynamic behavior of cam mechanisms, this study addresses the need to clarify the influence of geometrical parameters and technological conditions on some indicators of the jump phenomenon in contact loss for a cam-follower mechanism. This particularly developed case study referred to a mechanism with a profiled grooved disk cam and oscillating follower. To highlight the influence of the cam-follower contact elasticity on the jump phenomenon, two dynamic models were developed: one considering rigid elements in contact and the second considering elastic cam-follower contact. The models were tested within a virtually simulated experiment, and the numerical simulation results evidenced the influence of input factors like the applied load on the mechanism, the clearance in the cam-follower kinematic pair, and the rotational speed of the cam, and the inertia moment was reduced to the follower on some indicators of the jump phenomenon. Validation FEA and experiments were performed, proving the reliable appropriateness of the dynamic model based on elastic cam-follower contact.
25 December 2020 in IOP Conference Series: Materials Science and Engineering
This paper presents a dynamic study of a complex gear transmission. The kinematics is presented. The parameters of dynamic model are presented. The differential equation of kinetic energy is written. Some discussions are made regarding the work of the mechanism. The aspects discussed in the paper are useful to those who design such mechanisms.
The surfaces of the mechanical parts involved in friction processes are made using different processing methods. Each of these processing methods leads to a certain profile of the asperities of the generated surfaces. When such surfaces are subjected to friction processes, it is possible to produce a change in time in the magnitude of the friction coefficient. For experimental research, the outer cylindrical surfaces of some steel test samples were generated using various machining methods such as turning, grinding, ball and diamond burnishing, and vibroburnishing. Later, using a device adapted to a lathe, experimental tests were carried out following the time variation of the value of the friction coefficient under conditions of dry friction and lubricated friction, respectively. The results of the experimental tests were processed mathematically, being determined by empirical mathematical models that highlight the influence of the final processing methods of the surface, the presence of the lubricant, and the test duration on the variation of the friction coefficient. It was found that first, there is an increase over time in the values of the friction coefficient, and then the values of this coefficient stabilize at certain values. The increase in the coefficient of friction until reaching the stabilization value takes place in a proportion of approximately 148–305%.
10 December 2024 in Materials Research Proceedings
Activities within LCSA approaches targeting Sustainable Product, Process or Project Development, and eventually Societal Resilience usually involve multidisciplinary complexity in inventorying process variables in terms of defining materials, processes, energy consumptions, different categories of costs, or social factors. As long as Design Thinking is gaining field as a general philosophy in many kinds of businesses, for dealing with the more complex problems of design management, the particular idea of the presented research is to consider Axiomatic Design theory as a valuable tool for mastering industrial process variables inventorying. The included case study approaches the problem of analytically inventorying the process variables for sustainably developing a project for a wood pellets micro-production activity supplied from willow crops or alternative biomass resources.
Integration of thermographic imaging with in situ scanning electron microscopy (SEM) analysis may aid in quantifying thermal–mechanical behavior during tensile testing of 3D-printed polymers, which gives information about fracture mechanics, including the associated thermal phenomena. Upon fracture, samples exhibit changes in the thermal field, which is interesting because temperature fluctuations can affect material integrity. The paper introduces printing parameters to demonstrate a thermal measurement system’s sensitivity in detecting variations in mechanical response due to controlled changes in the process. Employing scientific methods, one can extrapolate results to a wider class of materials such as thermoplastics. Analysis of variance (ANOVA) is key in the design of experiments (DOE) if one wants to analyze the effect of factors and interactions. It has been used with the purpose of reducing the risk of type I errors (i.e., false positives). The finite element method (FEM) highlights temperature distribution in the area of interest and confirms recorded data. The particularly developed research experiments are carried out in a laboratory environment. Different samples are subjected to tensile tests under the evaluation of changes in the thermal field. SEM analysis is also widely used in fracture analysis to understand failure modes (ductile vs. brittle, crazing, delamination, and others). Thus, the paper aims to present a custom setup comprised a thermal camera pointed at samples during tensile testing that would serve as a reliable assessment system that accounts for the substitution of a sensor-based environment but is still fully capable of validating the measurement approach.