Alessio Facello

Dr. Alessio Facello

INRiM - Istituto Nazionale di Ricerca Metrologica, Turin, Piedmont, Italy
orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 January 2012 in Scandinavian Journal of Forest Research
Verified
Journal Article
Closed access
Raffaele SpinelliRaffaele Spinelli
Raffaele Spinelli
Eugenio CavalloEugenio Cavallo
Eugenio Cavallo
AFAlessio Facello
Alessio Facello
NMNatascia Magagnotti
Natascia Magagnotti
Carla NatiCarla Nati
Carla Nati
GPGiuseppe Paletto
Giuseppe Paletto
Comminution is a critical process in biomass supply chains and can be conducted with either chippers or grinders. These machines use different work tools(knives and hammers, respectively) and are applied to different feedstock types, but few studies are available on the inherent differences between the two technologies. A versatile grinder, alternatively equipped with hammers and knives, was studied to investigate the effect of tool type on machine productivity, fuel consumption, and product quality.The machine was powered by an agricultural tractor rigged with a flow meter, a torque meter, and shaft revolution meter for determining fuel consumption, power output, and engine speed. Three different feedstock types were processed: discarded pallets, solid logs, and residues from park maintenance, the latter consisting of branches from ornamental tree and shrub species. Depending on feedstock type, the knife configuration was 30–80% (average 50%) more productive than the hammer configuration and required 15–30% (average 24%) less energy per unit of product. Fuel consumption per dry ton was 30–75% (average 52%) higher for the hammer configuration. That held true for all feedstock types. Product quality was better for the knife configuration, except for park maintenance residues. In general, hammers should be limited to product with severe contamination that prevents the efficient use of knives.

1 July 2012 in Fuel Processing Technology
Verified
Journal Article
Closed access
Raffaele SpinelliRaffaele Spinelli
Raffaele Spinelli
Eugenio CavalloEugenio Cavallo
Eugenio Cavallo
AFAlessio Facello
Alessio Facello

2 July 2013 in Spanish Journal of Agricultural Research
Verified
Journal Article
Open access
PDF file
Niccolò PampuroNiccolò Pampuro
Niccolò Pampuro
AFAlessio Facello
Alessio Facello
Eugenio CavalloEugenio Cavallo
Eugenio Cavallo
Compost derived from swine solid fraction is a low density material (bulk density less than 500 kg m-3). This makes it costly to transport from production sites to areas where it could be effectively utilized for value-added applications such as in soil fertilization. Densification is one possible way to enhance the storage and transportation of the compost. This study therefore investigates the effect of pressure (20-110 MPa) and pressure application time (5-120 s) on the compaction characteristics of compost derived from swine solid fraction. Two different types of material have been used: composted swine solid fraction derived from mechanical separation and compost obtained by mixing the first material with wood chips. Results obtained showed that both the pressure applied and the pressure application time significantly affect the density of the compacted samples; while the specific compression energy is significantly affected only by the pressure. Best predictor equations were developed to predict compact density and the specific compression energy required by the densification process. The specific compression energy values based on the results from this study (6-32 kJ kg-1) were significantly lower than the specific energy required to manufacture pellets from biomass feedstock (typically 19-90 kJ kg-1).

2 February 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
ELElia Landi
Elia Landi
Andrea PratoAndrea Prato
Andrea Prato
Ada FortAda Fort
Ada Fort
Marco MugnainiMarco Mugnaini
Marco Mugnaini
VVValerio Vignoli
Valerio Vignoli
ASAlessandro Schiavi
Alessandro Schiavi
In the field of vibration monitoring and control, the use of low-cost multicomponent MEMS-based accelerometer sensors is nowadays increasingly widespread. Such sensors allow implementing lightweight monitoring systems with low management costs, low power consumption and a small size. However, for the monitoring systems to provide trustworthy and meaningful data, the high accuracy and reliability of sensors are essential requirements. Consequently, a metrological approach to the calibration of multi-component accelerometer sensors, including appropriate uncertainty evaluations, are necessary to guarantee traceability and reliability in the frequency domain of data provided, which nowadays is not fully available. In addition, recently developed metrological characterizations at the microscale level allow to provide detailed and accurate quantification of the enhanced technical performance and the responsiveness of these sensors. In this paper, a dynamic calibration procedure is applied to provide the sensitivity parameters of a low-cost, multicomponent MEMS sensor accelerometer prototype (MDUT), designed, developed and realized at the University of Siena, conceived for rolling bearings vibration monitoring in a broad frequency domain (from 10 Hz up to 25 kHz). The calibration and the metrological characterization of the MDUT are carried out by comparison to a reference standard transducer, at the Primary Vibration Laboratory of the National Institute of Metrological Research (INRiM).

30 May 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
LCLuciano Chiominto
Luciano Chiominto
Emanuela NataleEmanuela Natale
Emanuela Natale
Giulio D'EmiliaGiulio D'Emilia
Giulio D'Emilia
SGSante Grieco
Sante Grieco
Andrea PratoAndrea Prato
Andrea Prato
ASAlessandro Schiavi
Alessandro Schiavi
Sensors based on MEMS technology, in particular Inertial Measurement Units (IMUs), when installed on vehicles, provide a real-time full estimation of vehicles’ state vector (e.g., position, velocity, yaw angle, angular rate, acceleration), which is required for the planning and control of cars’ trajectories, as well as managing the in-car local navigation and positioning tasks. Moreover, data provided by the IMUs, integrated with the data of multiple inputs from other sensing systems (such as Lidar, cameras, and GPS) within the vehicle, and with the surrounding information exchanged in real time (vehicle to vehicle, vehicle to infrastructure, or vehicle to other entities), can be exploited to actualize the full implementation of “smart mobility” on a large scale. On the other hand, “smart mobility” (which is expected to improve road safety, reduce traffic congestion and environmental burden, and enhance the sustainability of mobility as a whole), to be safe and functional on a large scale, should be supported by highly accurate and trustworthy technologies based on precise and reliable sensors and systems. It is known that the accuracy and precision of data supplied by appropriately in-lab-calibrated IMUs (with respect to the primary or secondary standard in order to provide traceability to the International System of Units) allow guaranteeing high quality, reliable information managed by processing systems, since they are reproducible, repeatable, and traceable. In this work, the effective responsiveness and the related precision of digital IMUs, under sinusoidal linear and curvilinear motion conditions at 5 Hz, 10 Hz, and 20 Hz, are investigated on the basis of metrological approaches in laboratory standard conditions only. As a first step, in-lab calibrations allow one to reduce the variables of uncontrolled boundary conditions (e.g., occurring in vehicles in on-site tests) in order to identify the IMUs’ sensitivity in a stable and reproducible environment. For this purpose, a new calibration system, based on an oscillating rotating table was developed to reproduce the dynamic conditions of use in the field, and the results are compared with calibration data obtained on linear calibration benches.

27 March 2025 in IEEE Sensors Journal
Verified
Journal Article
Open access
ELElia Landi
Elia Landi
TBTommaso Lisini Baldi
Tommaso Lisini Baldi
JPJonas Papenbrock
Jonas Papenbrock
AFAlessio Facello
Alessio Facello
APAndrea Prato
Andrea Prato
Ada FortAda Fort
Ada Fort
In the practical implementation of soft robots, accurately tracking the deformation of links (or joints) is crucial for obtaining proper control. Therefore, there is a need for lightweight, durable, and cost-effective solutions to monitor the movement of soft segments. This study proposes sensor-equipped flexible joints capable of measuring the angle between the segments of a robotic finger, considering pure in-in-plane bending. Initially, these joints were simulated to assess their mechanical behavior and the feasibility of accommodating strain gauges to measure differential strain, which correlates with angle measurements. Based on the simulation results, three types of sensor-equipped joints with distinct mechanical properties were developed. These joints were characterized in terms of angle measurement accuracy and durability. The experimental evaluation assessed that maximum error, compared to an accurate reference angle measured using a MEMS accelerometer, was less than 1.5°. Durability tests demonstrated that joint performance remained stable over more than 3500 bending cycles, during which the joints were bent up to approximately 65°; the measured angle drift remained below 2°.