The increase in demand, and thus the need to lower its price, has kept C-based fuels as the main source. In this context, the use of oil and gas has led to increased climate change, resulting in greenhouse gases. The high percentage of eissions, over 40%, is due to the production of electricity, heat, or/and energy transport. This is the main reason for global warming and the extreme and increasingly common climate change occurrences, with all of nature being affected. Due to this reason, in more and more countries, there is an increased interest in renewable energies from sustainable sources, with a particular emphasis on decarbonisation. One of the energies analysed for decarbonisation that will play a role in future energy systems is hydrogen. The development of hydrogen–natural gas mixtures is a major challenge in the field of energy and fuel technology. This article aims to highlight the major challenges associated with researching hydrogen–natural gas blends. Meeting this challenge requires a comprehensive research and development effort, including exploring appropriate blending techniques, optimising performance, addressing infrastructure requirements, and considering regulatory considerations. Overcoming this challenge will enable the full potential of hydrogen–natural gas blends to be realised as a clean and sustainable energy source. This will contribute to the global transition to a greener and more sustainable future. Several international, European, and Romanian studies, projects, and legislative problems are being analysed. The mix between H2 and natural gas decreases fugitive emissions. In contrast, using hydrogen increases the risk of fire more than using natural gas because hydrogen is a light gas that easily escapes and ignites at almost any concentration in the air.
This study focuses on optimizing the storage capacity of an underground natural gas storage facility through numerical modeling and simulation techniques. The reservoir, characterized by an elongated dome structure, was discretized into approximately 16,000 cells. Simulations were conducted using key parameters such as permeability (10–70 mD) and porosity (12–26%) to assess the dynamics of gas injection and pressure distribution. The model incorporated core and petrophysical data to accurately represent the reservoir’s behavior. By integrating new wells in areas with storage deficits, the model demonstrated improvements in storage efficiency and pressure uniformity. The introduction of additional wells led to a significant increase in storage volume from 380 to 512 million Sm³ and optimized the injection process by reducing the storage period by 25%. The study concludes that reservoir performance can be enhanced with targeted well placement and customized flow rates, resulting in both increased storage capacity and economic benefits.
29 December 2021 in Journal of Petroleum Exploration and Production Technology
As air pollution has become a major issue in nowadays world, reducing methane emissions from the natural gas transmission systems is an issue that definitely has to be addressed. In order to do that, there are a few solutions available, such as the replacement of steel pipes with high-density polyethylene (HDPE) pipes. The main causes of these leaks are the corrosion defects and third-party interventions. The paper presents a new methodology for technological gas loss calculation from the natural gas transmission system. In order to obtain the most accurate calculation formulas, the flow coefficients for different cases were determined by experimental measurements. The paper presents the details regarding the construction and equipment of the experimental stand, as well as a new method for calculating the volumes of gas lost due to defects of this type. Thus, the aerial and buried defects were studied and the results obtained on statistical data were verified. Using the results of the study, the average emission of CH4 per year in Romania was calculated, and it was proven to be about 30% bigger than the European average. The findings of this study can help for a better understanding of the level of the losses and the effect on the final costs for the population, as well as the negative impact on the environment, in case the transporter does not take any measures.
In the context of intensifying global efforts to mitigate climate change, methane emissions from the oil and gas sector have emerged as a critical environmental and regulatory challenge, given methane’s high global warming potential over short timeframes. This study investigates methane emissions from representative extraction and production of oil and gas facilities in Romania, focusing on fugitive emissions from wells and associated processing infrastructure. The research is grounded in the implementation of a comprehensive Leak Detection and Repair (LDAR) program, aligned with OGMP 2.0 standards, and utilizes advanced detection technologies such as Flame Ionization Detectors (FID), Optical Gas Imaging (OGI), and Quantitative Optical Gas Imaging (QOGI). A systematic inventory and screening of thousands of components enabled the precise identification and quantification of methane leaks, providing actionable data for maintenance and emissions management. The findings highlight that, although the proportion of leaking components is relatively low, cumulative emissions are significant, with block valves, connectors, and compressor shaft seals identified as the most frequent sources of major leaks. The study underscores the importance of rigorous preventive and corrective maintenance, rapid leak remediation, and the adoption of modern detection and continuous monitoring technologies. The approach developed offers a robust framework for regulatory compliance and supports the transition from inventory-based to measurement-based emissions reporting, in line with recent European regulations. Ultimately, effective methane management not only fulfills environmental obligations but also delivers economic benefits by reducing product losses and enhancing operational efficiency, contributing to the decarbonization and sustainability objectives of the energy sector.
Water-based drilling fluids (WBDFs) are widely used due to their economic and environmental advantages; however, shale hydration remains a major limitation. This study evaluates Fe2O3, CuO, ZnO, and MgO nanocrystalline metal oxides synthesized via co-precipitation as inorganic shale inhibitors for WBDFs. Comprehensive characterization confirmed phase-pure nanocrystalline oxides (17–38 nm) with high thermal stability. Performance tests revealed that MgO-based WBDF exhibited the lowest plastic viscosity (17 cP), the highest pH (≈10.0), and the strongest shale inhibition (6.1% swelling), while Fe2O3 provided superior filtration control (6.0 mL). CuO showed balanced rheology, whereas ZnO displayed comparatively weaker inhibition. Compared with commercial inhibitors (Amine NF and Glycol), MgO- and Fe2O3-based systems achieved comparable or improved performance with enhanced thermal and environmental robustness. These results demonstrate the potential of nanocrystalline metal oxides as sustainable additives for improving WBDF performance under high-pressure, high-temperature (HPHT) conditions.
Water-based drilling fluids (WBMs) are widely applied in petroleum engineering due to their lower cost and reduced environmental impact compared to oil-based muds. However, their performance is severely limited in shale formations, where hydration and swelling of clay minerals lead to wellbore instability. In this study, two novel imidazoline-type inhibitors were synthesized from fatty acids: A-Lin (derived from linoleic acid) and A-Lau (derived from lauric acid). The synthesis involved amidation followed by cyclization, and the products were characterized using FTIR and TGA. Their performance as shale hydration inhibitors was evaluated in WBM formulations and compared with commercial additives (Amine NF and Glycol). The FTIR spectra confirmed successful imidazoline ring formation, while TGA demonstrated good thermal stability up to 150 °C, with A-Lin exhibiting superior resistance due to its unsaturated structure. Rheological tests showed that the synthesized additives reduced plastic viscosity, thereby improving cuttings transport efficiency. Swelling tests revealed that A-Lin achieved the lowest final swelling (6.3%), outperforming both commercial inhibitors and the saturated A-Lau analogue. Furthermore, A-Lin provided the best lubricity coefficient (0.148), reducing torque and drag during drilling. Overall, A-Lin demonstrated strong potential as an efficient, thermally stable, and environmentally compatible shale inhibitor for advanced WBM formulations. Compared to conventional inhibitors such as KCl, glycol, and amine-based additives, A-Lin uniquely combines superior swelling inhibition, enhanced lubricity, and good thermal stability, highlighting its novelty as an imidazoline derivative derived from renewable fatty acids