For sustainable energy storage, all‐organic batteries based on redox‐active polymers promise to become an alternative to lithium ion batteries. Yet, polymers contribute to the goal of an all‐organic cell as electrodes or as solid electrolytes. Here, we replace the electrolyte with a deep eutectic solvent (DES) composed of sodium bis(trifluoromethanesulfonyl)imide (NaTFSI) and N‐methylacetamide (NMA), while using poly(2,2,6,6‐tetramethylpiperidin‐1‐yl‐oxyl methacrylate) (PTMA) as cathode. The successful combination of a DES with a polymer electrode is reported here for the first time. The electrochemical stability of PTMA electrodes in the DES at the eutectic molar ratio of 1 : 6 is comparable to conventional battery electrolytes. More viscous electrolytes with higher salt concentration can hinder cycling at high rates. Lower salt concentration leads to decreasing capacities and faster decomposition. The eutectic mixture of 1 : 6 is best suited uniting high stability and moderate viscosity.
The electrodeposition of copper onto Au(111) from Deep Eutectic Solvents (DESs) type III has been studied by cyclic voltammetry. Investigations were carried out with mixtures of choline chloride (ChCl) and ethylene glycol (EG) or trifluoroacetamide (TFA). The eutectic compositions and temperatures were determined by differential scanning calorimetry (DSC). For the ChCl/EG DES, a eutectic ratio of 16 : 84 (ChCl:EG) was found instead of the previously reported ratio of 33 : 67. The electrodeposition of copper was studied for electrolytes with different ratios of ChCl to hydrogen bond donor (HBD) to resolve the influence of the composition on the deposition behavior. Both CuCl and CuCl2 were used as Cu salts. Underpotential deposition (UPD) is followed by bulk deposition with the diffusion rate of Cu species being dependent on the ratio of ChCl to HBD. With CuCl2, both Cu+ and Cu2+ species are reduced and deposited, whereby the two‐electron reduction is more dominant with higher chloride content and presence of EG. However, the properties of the Cu electrodeposition do not result from the freezing‐point depression of the DESs, but from the high concentration of ions.
23 August 2021 in Angewandte Chemie International Edition
While numerous reference electrodes suitable for aqueous electrolytes exist, there is no well‐defined standard for non‐aqueous electrolytes. Furthermore, reference electrodes are often large and do not meet the size requirements for small cells. In this work, we present a simple method for fabricating stable 3D‐printed micro‐reference electrodes. The prints are made from polyvinylidene fluoride, which is chemically inert in strong acids, bases, and commonly used non‐aqueous solvents. We chose six different reference systems based on Ag, Cu, Zn, and Na, including three aqueous and three non‐aqueous systems to demonstrate the versatility of the approach. Subsequently, we conducted cyclic voltammetry experiments and measured the potential difference between the aqueous homemade reference electrodes and a commercial Ag/AgCl‐electrode. For the non‐aqueous reference electrodes, we chose the ferrocene redox couple as an internal standard. From these measurements, we deduced that this new class of micro‐reference electrodes is leak‐tight and shows a stable electrode potential.
Copper electrodeposition on Au(111) from deep eutectic solvents (DESs) type III was investigated employing cyclic voltammetry as well as chronoamperometry. It was further examined on Au(poly) using the electrochemical quartz crystal microbalance (EQCM). The employed DESs are mixtures of choline chloride (ChCl) or choline nitrate (ChNO3) with ethylene glycol (EG) as hydrogen bond donor (HBD), each in a molar ratio of 1 : 2. CuCl, CuCl2, or Cu(NO3)2 ⋅ 3H2O were added as copper sources. Underpotential deposition (UPD) of Cu precedes bulk deposition in chloride as well as nitrate electrolytes. Cu deposition from Cu+ in chloride media is observed as a one‐electron reaction, whereas deposition from Cu2+ occurs in two steps since Cu+ is strongly stabilized by chloride. Cu+ is less stabilized by nitrate and the beginning of bulk deposition in the nitrate‐containing DES with Cu2+ is shifted by several hundred mV to more positive potentials compared to the chloride DES. A diffusion‐controlled, three‐dimensional nucleation and growth mechanism is found by chronoamperometric measurements and analysis based on the model of Scharifker and Mostany.
The electrochemical behavior of Au(111) in contact with deep eutectic solvents (DESs) was studied by cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and immersion experiments to determine the potential of zero total charge (pztc). In particular, DESs type III consisting of a choline salt and a hydrogen bond donor (HBD) were investigated. The HBDs urea and ethylene glycol (EG) were chosen since they belong, in combination with choline chloride (ChCl), to the most widely studied systems. A third HBD used in this study was trifluoroacetamide (TFAcA) because of its remarkable freezing point depression. The adsorption of chloride, nitrate, and sulfate anions on Au(111) was investigated using DESs, as the electrochemical behavior of Au(111) in aqueous electrolytes containing these anions were already well studied. For a better understanding of the interactions of ions in DESs with noble metal electrode surfaces, Au(111) in aqueous ChCl was investigated as well. It was shown that anion adsorption on Au(111) in the DESs under consideration was similar to adsorption in the respective dilute aqueous systems.