4 November 2019 in IEEE Transactions on Applied Superconductivity
This paper puts forward a method based on high temperature superconducting (HTS) current limiting technology, to improve the over-current stability for a battery unit in a superconducting magnetic energy storage (SMES)-battery hybrid energy storage systems (HESS). In contrast to supercapacitors, flywheels and other energy storage systems, SMES-battery HESS possess the technical properties of power capacity, energy and response speed, among other. Thus, SMES-battery HESS may be utilized to handle power swing, energy transfer, voltage fluctuation and related transient stability issues. But an over-current in a battery unit is harm to its cycle life of the battery. Hence, the internal protection system of the battery unit is used to remove a fault by cutting off its outputs. In this paper, a ${\rm{YBa_{2}Cu_{3}O_{7-X}\ (YBCO)}}$ thin film is employed as the protection device to limit the over-current in a battery unit. In normal operation, the thin film is in the superconducting state, and its influence on the system can be ignored. An over-current will be limited evidently lower than the action threshold of the internal protection system by the quench resistance of the thin film. Therefore, the whole outputs of a battery unit will not be interrupted and restarted. Through the verification experiment carried out in our laboratory, the proposed protection method operated as expected, and the stability, as well as the reliability of the battery unit, could be improved.
12 July 2019 in IEEE Transactions on Plasma Science
Synchronous induction coilgun (SICG) has attracted more and more attention due to its advantages of simple manufacturing and no physical contact between armature and barrel. The armature, as an important component of SICG, will directly affect the launch speed and energy conversion efficiency. According to the distribution characteristics of eddy current and electromagnetic force, a new structural armature is proposed in this paper. The proposed inner conical armature is characterized by the maximum thickness at the tail end and the minimum thickness at the front end, with a gradual decrease in the thickness along the axial direction. The simulation results reveal that the proposed armature not only increases the mutual inductance between the armature and the drive coil but also enhances the electromagnetic force and weakens the armature capture effect. The experimental results verify that, compared with a traditional armature weighing 56.5 g, the new structure armature weighing 58.0 g enables higher muzzle velocities using the same set of pulsed power supply and drive coil, providing higher efficiency.
13 August 2019 in IEEE Access
A new type of multipole field electromagnetic launcher is designed in this paper, which has two parallel layers of multipole structure, and there is a 30-degree relative torsion angle between the inner and the outer one. The armature is designed as a complete and symmetrical hollow cylindrical metal sleeve with no slots. Owing to the superposition of the magnetic fields generated by the two layers, this novel structure can make the magnetic field density and eddy current distribution on the armature unbalanced, which generates an axial force and torque simultaneously. Simulations were conducted, and the magnetic field and the eddy current distribution were analyzed. The simulations indicate that this double-layer multipole field electromagnetic launcher achieves a rotational motion and a higher linear speed than that of single-layer structure. Experiments were performed and the results verified the correctness of the simulations. Due to its rotational performance, this configuration provides an approach to obtain gyroscopic stabilization for projectiles. It creates condition for multi-stage and combined mode applications because the armature does not need to be processed particularly to meet special requirements.
18 November 2018 in IEEE Transactions on Applied Superconductivity
Researches on the synchronous parallel discharge of multimodule pulsed power supply have confirmed that it can output large pulse currents with high amplitude. For electromagnetic railguns, excess current may cause orbital erosion and other problems, and the ideal driving current is rectangular pulse currents. Therefore, the asynchronous discharge of multimodule superconducting pulsed power supply (SPPS) is studied in this paper to reduce the amplitude and increase the pulsewidth for driving an electromagnetic railgun. A toroidal SPPS based on eight coupled high-temperature superconducting pulsed power transformers and a dynamic simulation model of electromagnetic railgun is established. The simulation results show that armature currents with different amplitude and pulsewidth can be obtained by adjusting the trigger delay time of each module. With the increase of the trigger delay time, the amplitude decreases but the pulsewidth increases. With a set of trigger delay time, the asynchronous discharge of the eight-module SPPS can output an approximate rectangular pulse current with amplitude of 126 kA. The armature and projectile with a total mass of 50 g can be accelerated to 346 m/s, giving the efficiency of 16.2%.
12 April 2019 in IEEE Transactions on Plasma Science
This paper proposes a novel single-stage double-layer saddle multipole field electromagnetic launcher (SSDFEL), which combines the characteristics of reconnection gun to achieve simultaneous linear acceleration and gyroscopic stabilization of the projectile. Since the saddle driving coils are divided into two layers, the magnetic field density inside the launcher is enhanced. The eddy current induced on the inner and outer surfaces of the projectile is greatly changed by the hollow cylindrical projectile with six symmetrical vertical slots twisted at a certain angle, and the projectile is simultaneously propelled to perform rotation motion and linear motion. In this paper, the electromagnetic field finite-element software is used to simulate and calculate this model. The simulation results indicated that the double-layer driving coil distribution has larger axial acceleration force and bigger circumferential torque than that of the single-layer driving coil distribution, the energy conversion efficiency has also been obviously increased, and there is an optimal initial twisted angle, which accelerates the projectile to the peak of rotation. To verify the results, an SSDFEL was established and tested. The experiment results confirm that the rotation performance can be affected by the initial twisted angle and a better launching effect is achieved than a single-layer distribution. In general, the experimental results are in agreement with the simulation results.