Thien Xuan Dinh

Thien Xuan Dinh

Auto-generated profile, based on publicly available information

Thien Xuan Dinh

Ritsumeikan University

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2023 in Physics of Fluids
Verified
Journal Article
Open access
PDF file
LMLuan Ngoc Mai
Luan Ngoc Mai
TVTrung Hieu Vu
Trung Hieu Vu
TDThien Xuan Dinh
Thien Xuan Dinh
HVHoai Duc Vu
Hoai Duc Vu
CTCanh-Dung Tran
Canh-Dung Tran
HNHieu Khanh Ngo
Hieu Khanh Ngo
In this paper, the behavior of the cone-jet mode of fluid by electrohydrodynamic atomization (electrospray) is numerically simulated and investigated with the effect of liquid wetting and corona discharge effects. The simulation was performed with contact angle condition to fit the Taylor cone shape by experiments. Experimental data are provided to verify and validate the numerical method, followed by additional analyses on the effects of electrical conductivity, surface tension, flow rate, and fluid viscosity on the electrospray characteristics, including spray current and jet diameter. Numerical results by simulations are in reasonable agreement with experiments and consistent with the literature. Analyses on different contact angles suggest potentially major impacts of this factor on the cone-jet mode in high voltage and low flow rate circumstances. Furthermore, the influence of corona discharge on electrospray is also investigated by both electrospray–corona simulation and experiment using a high-speed camera, yielding a significant improvement in the numerical prediction for Taylor cone formation. Numerical results indicate that liquid wetting on capillary nozzles would be a vital factor for the Taylor cone formation in numerical electrospray–corona discharge studies.

11 September 2020 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
NVNgoc Tran Van
Ngoc Tran Van
Van DauVan Dau
Van Dau
CTCanh-Dung Tran
Canh-Dung Tran
TDThien Xuan Dinh
Thien Xuan Dinh
HTHoa Phan Thanh
Hoa Phan Thanh
TBTung Bui
Tung Bui

1 July 2012
Verified
Conference Paper
Closed access
PLP. H. Le
P. H. Le
TDT. X. Dinh
T. X. Dinh
AMA. Mitani
A. Mitani
Shinichi HiraiShinichi Hirai
Shinichi Hirai
In this study, we perform an experiment and develop a dynamic model that describes the planar motion modes of a micro-part, including two linear motions and one rotational motion, on a saw-tooth surface. In the experiment, the planar motion of the micro-part is obtained by a particle-tracking method. The rotation angle is measured from the principal axis of the micro-part image. In a simulation, contact between the micro-part and the saw-tooth surface is assumed to be the contact between a number of hemispheres on the micropart and the surface, which results in either a point contact or slope contact. The effect of the saw-tooth surface roughness on the contact force at each contact point is modeled as a field of normal vectors. In addition, the roughness of the saw-tooth surface is approximated by superposing white noise on an ideal saw-tooth profile and is used to evaluate the adhesion force. The results show that the model describes the motion modes of a micro-part. Furthermore, the simulated results of the two linear motions are in good agreement with our experimental results from a previous study. The proposed model can be used to improve the design of surfaces for micro-part transport.

1 January 2012 in The Proceedings of Mechanical Engineering Congress, Japan
Verified
Journal Article
Open access
PDF file
TDThien Dinh
Thien Dinh
YOYoshifumi Ogami
Yoshifumi Ogami
In this paper, we present the design and simulation of a microelectromechanical system (MEMS)-based fluidic angular rate sensor that can simultaneously detect two components of angular rate (two degrees of freedom). The sensor includes three layers in which only the layer containing in-plane hotwires requires a standard MEMS process. The other layers can be fabricated by either hot embossing or conventional machining. In the sensor, four jets comprising two perpendicular pairs of flows are generated by a piezoelectric actuator through a valveless network channel. We consider two designs to optimize the gyroscope structure with the objective function relating the output voltage to the angular rate.

1 January 2009 in The Proceedings of Conference of Kansai Branch
Verified
Journal Article
Open access
PDF file
TDThien Xuan Dinh
Thien Xuan Dinh

1 August 2013 in Advanced Materials Research
Verified
Journal Article
Closed access
PDF file
PLPhuong Hoai Le
Phuong Hoai Le
TDThien Xuan Dinh
Thien Xuan Dinh
AMAtsushi Mitani
Atsushi Mitani
Shinichi HiraiShinichi Hirai
Shinichi Hirai
In this work, we study experimentally the effect of the geometry parameters of saw-tooth surface and micro-part on the motion of micro-parts. The experiments are performed for a range of saw-tooth pitch, p, micro-part length, l, and exciting frequency applied to the surface, f. By the use of particle tracking velocimetry method, we can achieve time-dependent velocity, and then ensemble-averaged velocity of the micro-parts. The results show that for different l and p but the same relative scale l/p, the profiles of micro-part velocity against the characteristic surface velocity pf are similar. However, they shift along pf axis depending on p. Furthermore, the profiles are the similar for the relative scale l/p of 4 to 100. It seems that the motion of micro-part depends on characteristic surface velocity pf than the relative scale l/p for l/p larger than a certain value.